Honeywell DIAL-SET DS05C Product Data Download Page 3

DS05C,D,G

3

62-3041—4

Water Capacities (See Table 1)

The suitability of a given regulator size is dependent on the 

pressure requirements where it will operate. For the pressure 

regulator valve size required for a specific installation, 

determine the following:

1.

Pressure differential between inlet and outlet pressure in 

pounds per square inch (psi),

2.

Capacity in gallons per minute, and

3.

Allowable reduced pressure falloff in psi.

Given these variables, use Table 1 to determine the proper 

size pressure regulator valve for your application.

Example: An installation has 135 psi inlet pressure, 60 psi 

outlet pressure (75 psi pressure differential). If a 12 gpm 

capacity is required with only 10 psi falloff allowable, a 1/2 in. 

DS05 is required.

Table 1. Water Capacities.

Pressure 

Regulator 

Valve Size

Reduced 

Pressure 

Falloff 

(psi)

Pressure Differential Between Inlet and Outlet

25 psi

50 psi

75 psi

100 psi or more

Flow 

Capacity 

(US gpm)

Velocity 

(ft/sec)

a

a

Velocity in feet per second is based on schedule 40 pipe size. Recommended pressure falloff for general use is approximately 

104 kPa (15 psi). Recommended velocities for the flow of water: residential and general use, 5 to 10 ft/sec; industrial use, 7 to 15 

ft/sec; boiler feed, 7 to 15 ft/sec.

Flow 

Capacity 

(US gpm)

Velocity 

(ft/sec)

a

Flow 

Capacity 

(US gpm)

Velocity 

(ft/sec)

a

Flow 

Capacity 

(US gpm)

Velocity 

(ft/sec)

a

1/2 inch

6

1.2

1.3

2.3

2.4

3.3

3.5

4.4

4.6

10

8.8

9.3

10.1

10.7

10.6

11.2

10.6

11.2

15

13.2

13.9

15.0

15.8

17.6

18.6

17.6

18.6

20

17.6

18.6

20.7

21.9

22.0

23.2

22.9

24.2

3/4 inch

6

3.6

2.1

4.0

2.4

4.0

2.4

4.0

2.4

10

8.1

4.9

9.3

5.6

9.9

6.0

9.9

6.0

15

14.7

8.8

17.6

10.6

19.8

11.9

20.6

12.4

20

23.0

13.8

27.7

16.7

32.1

19.3

4.1

20.5

1 inch

6

5.7

2.1

5.9

2.2

5.9

2.2

6.3

2.4

10

13.2

4.9

15.4

5.7

15.7

5.8

16.4

6.1

15

19.6

7.3

24.6

9.1

18.6

10.6

31.7

10.8

20

25.7

9.6

32.1

11.9

37.6

14.0

43.6

16.2

1-1/4 inch

6

13.5

2.6

16.0

3.4

20.0

4.3

22.0

4.7

10

22.0

4.7

29.0

6.2

34.0

7.3

38.0

8.1

15

37.0

7.9

56.0

12.0

62.5

13.4

73.0

15.6

20

55.0

11.8

78.0

16.7

87.0

18.6

101.0

21.6

Summary of Contents for DIAL-SET DS05C









Reviews: