manualshive.com logo in svg

Honeywell CT3451, Owner'S Manual, Page: 6 / 12

Share
Download
Honeywell CT3451 Owner'S Manual Download Page 6

CT3451 PROGRAMMABLE THERMOSTAT

69-1620—1

6

Fig. 13. Installing batteries.

❑

Restore power to the heating/cooling system.

8 CUSTOMIZE YOUR THERMOSTAT

Your Honeywell thermostat comes preset to the most 
commonly used settings:
— Temperature (°F). 
— Gas or oil forced air furnace.
— Aggressive algorithm control.
 

You can change these settings using the instructions that 
follow. To exit at any time, press the  

▲ 

key until End 

displays.

Setting °F/°C Indication, Heat Cycle Rate, 

Heating/Cooling Temperature Control

The following instructions provide information to change 
the heating cycle rate to match the heating equipment 
and to choose either the Fahrenheit (°F) or Celsius (°C) 
display.

NOTE: All four steps must be completed to save 

changes to the °F/°C indication and the heat 
cycle rate.

❑

Enter Installer Setup.
— Use 

▼ 

or 

▲

 keys to set the temperature setpoint 

to 52°F (11°C).

— Press 

▼ 

and 

▲

 keys simultaneously for more 

than two seconds to enter Installer Setup.

— Release the keys to display the three-digit soft-

ware revision code. (Information displayed varies 
by model).

— Press the 

▲

 key. FC (factory configuration) dis-

plays. (A typical example is shown, but informa-
tion displayed varies by model. This information 
is for factory use only.)

❑

Setting °C or °F.
— Press the 

▲

 key again to display the current 

setting.

— Press the 

▼

 key to change the °C or °F indication.

❑

Setting Heat Cycle Rate (see Table 2 for the cycle rate 
options and equipment).
— Press the  

▲

 key to display the current heat cycle 

rate setting of 1, 3, 4, 5, 9, or 12 cph.

— If the desired cycle rate is displayed, press the 

▲

 

key to display heating and cooling algorithm 
default.

— To change the heat cycle rate, press the 

▼

 key 

until your choice of 1, 3, 4, 5, 6, 9, or 12 is dis-
played.

— Press the 

▲

 key to display the heating and 

cooling temperature control algorithm configura-
tion default.

— Press the 

▼

 key to change the heating and cool-

ing control algorithm to C1 or C3.

C1 = Standard control algorithm.
C3 = Aggressive control algorithm (Default. Can 
cause overshooting.)

M20514

SYST

EM

Cool  Off  Heat 

Auto  On

FAN

Hold

Select

TUE

PM

AA BATTERIES (3)

M12582A

SET

HT.

M12583

M12584A

M12589A

M12588A

M14691

Summary of Contents for CT3451













Reviews:

No comments