Honeywell CP-645 Installation Instructions Manual Download Page 12

Page: 12 / 20

WEB-645, CP-645 NETWORK CONTROLLER

62-0432—01

OPTION CARD INSTALLATION (WEBS-AX UNITS ONLY)

The WEB-645-AX circuit board provides one 30-pin option card slot, compatible with WEB-200/600 style option cards. Option

card usage is supported only if the unit is configured with WEBs-AX (and

not

WEB R2).

WARNING

Power to the controller must be OFF when installing or removing an option card, or damage will occur!Also, you

must be very careful to plug an option card into the connector properly (pins aligned).

Refer to the installation document that accompanies a specific option card for complete details.

Table 4 lists the different option card types, with notes specific to the WEB-645-AX controller.

Installing an option card (WEBs-AX units only).

Installing an option card (WEBs-AX units only).

If applicable, backup the controller’s configuration to your PC using platform tools in WEBs-AX Workbench.

Stop

any running station, using the Application Director platform view.

Unplug the 6-position power connector from the circuit board.

Using a #2 Phillips head screwdriver, remove the two screws from the option card mounting posts, and set them aside.

Carefully insert the pins of the option card into the option card socket. The mounting holes on the option card should line up

with the standoffs on the base board. If they do not, the connector is not properly aligned. Press until the option card is

completely seated.

Place the custom end plate that came with the option card over the connector(s) of the option card.

Replace the two screws through the end plate and into the standoffs on the controller’s base board. Using a screwdriver,

hand tighten these screws.

Plug in the power connector in and verify operation.

MAINTAINING THE WEB-645-AX

This section provides information on the following topics:

• Cleaning

• Required Battery Maintenance

• Replacement Parts

• Replacing the WEB-645-AX circuit board

• Returning a Defective Unit

Cleaning

If dust or metal filings are present inside the unit, clean with vacuum or compressed air. Otherwise, no cleaning inside the unit is

required. Optionally, if the outside of the metal enclosure becomes dirty, you can wipe it with a damp cloth and mild detergent.

Table 4. Option card types and WEBs-AX notes.

Option card model/type

WEB-645-AX Notes

NPB-232 (Single RS-232 port)

Uses COM7

NPB-2X-485 (Dual RS-485 ports)

Uses COM7 and COM8

NPB-LON (LonWorks FTT-10)

Operates as LON2

NPB-GPRS-W (Wireless GPRS modem)

Uses COM7 and COM8

NPB-ZWAVE (Wireless Z-Wave serial

gateway)

Uses COM7

Summary of Contents for CP-645





















Search results

Summary of Contents for CP-645

Reviews:

Related manuals for CP-645

Brands by name

Popular brands

Honeywell CP-645, Installation Instructions Manual

Search results

Summary of Contents for CP-645

Reviews:

Related manuals for CP-645

Brands by name

Popular brands