manualshive.com logo in svg

Honeywell ControlEdge 900 platform, Hardware Planning And Installation Manual, Page: 61 / 230

Share
Download
Honeywell ControlEdge 900 platform Hardware Planning And Installation Manual Download Page 61

61

Table 5-1: I/O Rack Componets

Item Description

1

Rack, available in 4-, 8- or 12-slot versions

2

Power Supply

3

CPM or EPM with Security Cover

4

Grounding bars (for I/O wiring; optional; required for safety applications)

5

Input/Output modules

6

I/O Terminal Blocks

7

Power Status Module (PSM) (required if using redundant power supply)

Rack orientation and mounting

Racks must be mounted horizontally and must never be mounted
with the backplane flat on a horizontal panel or tabletop. This allows
airflow and ventilation through the racks. The Environmental
specifications provided in this guide apply only when using the
recommended mounting configuration.

Rack dimensions, including overall dimensions and patterns for
drilling holes for mounting, are provided in

Rack dimensions

section

and

Rack orientation and mounting

section.

Figure 5-6: Rack dimensions

Summary of Contents for ControlEdge 900 platform







































































































































































































































Reviews:

No comments