Honeywell ControlEdge 900 platform Hardware Planning And Installation Manual Download Page 53

Page: 53 / 230

CHAPTER

CONTROLEDGE 900 COMMON REFERENCE
INFORMATION

This section is applicable to both UOC and PLC systems and provides
the following information:

Installation

Wiring and cabling planning

Maintenance

Diagnostics and Troubleshooting

Special Condition of Use and Approved Standards

Installation

The topics covered in this chapter are:

See "Rack options" below for more information.

See "Rack Types" on page 55 for more information.

See "Rack installation" on page 64 for more information.

See "Power Supply" on page 77 for more information.

See "Environmental considerations" on page 81 for more
information.

See "ControlEdge 900 I/O " on page 87 for more information.

See "Terminal block styles" on page 100 for more information.

See "Terminal Block-to-Field (Signal) Wiring" on page 106 for
more information.

Rack options

I/O racks are available in 4-slot, 8-slot, and 12-slot versions and can
be utilized to house either a controller and I/O or as an I/O expansion
rack containing EPM and I/O.

Both 8-slot I/O rack and 12-slot I/O rack have two types of racks:

Summary of Contents for ControlEdge 900 platform







































































































































































































































Search results

Summary of Contents for ControlEdge 900 platform

Reviews:

Honeywell ControlEdge 900 platform, Hardware Planning And Installation Manual, Page: 53 / 230

Search results

Summary of Contents for ControlEdge 900 platform

Reviews: