Honeywell ControlEdge 900 platform Hardware Planning And Installation Manual Download Page 43 | Manualshive

Page: 43 / 230

Honeywell ControlEdge 900 platform Hardware Planning And Installation Manual Download Page 43

43

Component
Type

Comments

EPMs

while its ETH2 port is left disconnected. Before it is inserted into its
slot, the 100x rotary switch on the EPM board must be set to indicate
the type of network connectivity in use. This is done by setting it to
position 4. The IP address of the EPM is assigned by the UOC CPM
based on the module number set on the 10X and 1x rotary switches.
These switches must also be set before the EPM is inserted into its
slot.

Unmanaged
Switches

900 I/O racks with EPM gateways have been qualified to
communicate with UOC through unmanaged switches. EPMs may not
be connected through managed switches.

Stratix
Switches

EIP I/O, devices and PLCs may be connected to UOC through
qualified, Stratix managed switches. For further information on how to
deploy and configure Stratix switches, see

EtherNet IP User's Guide_

EPDOC-X399-en-510A.pdf

.

Following section provides information about installing racks, EPM,
power supply and so on.

Table 4-1: Reference for installing racks, EPM, power supply and so on

Components

Reference section

Racks

For information about options and types of racks, see the sections

and

. For information about installing

Racks, see the section

Rack Installation

EPM

For information about installing EPM, see the section

Processor Module

.

Power Supply

For information about connecting to AC or DC power supply, see
the section

.

Configuration

For information about configuration, refer to the Software
Configuration Guide.

Environmental

For information about environmental consideration to be taken
care, see the section

Environmental Considerations

.

Hardware configuration of UOC-CPM

For more information refer to the UOC User’s Guide (PLC to UOC
conversion).

«
...
41
42
43
44
45
...
»

Summary of Contents for ControlEdge 900 platform







































































































































































































































Reviews:

No comments