Honeywell ControlEdge 900 platform Hardware Planning And Installation Manual Download Page 122

Page: 122 / 230

AWG
No.

Diameter
inches

Type
K

Type
J

Type T

Type
E

Type S
Pt/
PT110

Type R
Pt/
PT113

Type
W5/
W26

Type
W/
W26

0.0100

5.984

3.551

3.043

7.169

1.85

1.91

2.38

2.03

Table values are shown as a reference only; actual values may vary. Consult
manufacturer specifications.

Isolation

This module has eight inputs, which are isolated except for RTD
current sources.

RTD Inputs

RTD inputs share current sources (two RTD inputs per source), as
shown below:

Figure 5-30: RTD Inputs

For example, the current source for the RTD input at channel one
(terminals 1 and 2) is terminal 3 (IRTD 1 & 2). This same current
source (IRTD 1 & 2) is also used for an RTD input at channel two
(terminals 4 and 5).

Figure on

RTD Inputs

and Figure on

Universal Analog Input Module

(UAI) Wiring

shows the examples of RTD input wiring (2-wire and 3-

wire RTDs). Four-wire RTD inputs are not available.

122

Summary of Contents for ControlEdge 900 platform







































































































































































































































Search results

Summary of Contents for ControlEdge 900 platform

Reviews:

Honeywell ControlEdge 900 platform, Hardware Planning And Installation Manual, Page: 122 / 230

Search results

Summary of Contents for ControlEdge 900 platform

Reviews: