Honeywell CGW-MB Installation And User Manual Download Page 76

Page: 76 / 187

CGW-MB Installation and Users’ Manual | P/N:LS10248-000HW-E | REV.G | JUL/31/2022

Device Types

Modbus Communications

7.30 Device Types

Device types are organized into the following categories:
•

Detectors (1–50) -

Table 7.39: "Device Type Values – Detectors"

•

Modules (51–150) -

Table 7.40: "Device Type Values – Modules"

Table 7.40: Device Type Values – Modules

Table 7.39: Device Type Values – Detectors

Device Type

Value

Device Type

Value

Not Identified

0000H

Wireless Smoke Photo
Tracking

0311H

Heat

0100H

Smoke Laser Latching

0400H

Heat (rate of rise)

0101H

Smoke Laser Tracking

0401H

Heat (fixed)

0102H

Duct Smoke Laser Latching

0402H

Heat (high heat)

0103H

Duct Smoke Laser Tracking

0403H

Wireless Heat

0110H

Air Reference Laser

0404H

Wireless Heat (rate of rise)

0111H

Smoke (Harsh)

0500H

Wireless Heat (fixed)

0112H

Smoke (Beam)

0501H

Wireless (high heat)

0113H

Smoke Multi

0600H

Smoke Ion Latching

0200H

Smoke Acclimate

0601H

Smoke Ion Tracking

0201H

Wireless Smoke Multi

0610H

Duct Smoke Ion Latching

0202H

Wireless Smoke Acclimate

0611H

Duct Smoke Ion Tracking

0203H

CO Alarm

0700H

Smoke Photo Latching

0300H

Fire/CO

0701H

Smoke Photo Tracking

0301H

Photo/CO

0702H

Duct Smoke Photo Latching

0302H

CO/Photo/Thermal/IR

0703H

Duct Smoke Photo Tracking

0303H

Aspiration

0801H

Smoke (Photo Flame)

0304H

Aspir. Ref

0802H

Wireless Smoke Photo
Latching

0310H

Device Type

Value

Device Type

Value

Not Identified

0000H

Acknowledge Switch

0041H

Heat Detection Circuit

0001H

Wireless Acknowledge Switch

0042H

Wireless Heat Detection
Circuit

0002H

All Call Page

0043H

Conventional Smoke

0003H

Drill Switch

0044H

Wireless Conventional
Smoke

0004H

Wireless Drill Switch

0045H

Smoke Detection

0005H

Evacuate Switch

0046H

Wireless Smoke Detection

0006H

Wireless Evacuate Switch

0047H

Monitor

0010H

Signals Silence Switch

0048H

Wireless Monitor

0011H

Wireless Signals Silence
Switch

0049H

Pull Station

0012H

Reset Switch

004AH

Wireless Pull Station

0013H

Wireless Reset Switch

004BH

Summary of Contents for CGW-MB




























































































































































































Search results

Summary of Contents for CGW-MB

Reviews:

Honeywell CGW-MB, Installation And User Manual, Page: 76 / 187

Search results

Summary of Contents for CGW-MB

Reviews: