Honeywell CGW-MB Installation And User Manual Download Page 24

Page: 24 / 187

CGW-MB Installation and Users’ Manual | P/N:LS10248-000HW-E | REV.G | JUL/31/2022

Section 4: Installation

You can use a portable CLSS Gateway mainboard in the fire detection system.

4.1 Mounting the Portable CLSS Gateway Mainboard

Refer to your panel documentation to know about mounting the CLSS Gateway
mainboard onto the panel.

4.1.1 Connecting to a Fire Alarm Panel

To know about supported panel variants, their connection options, and commissioning
procedure, refer to the

“Connecting to the Panels” on page 135

4.1.2 Connection Options

The CLSS Gateway mainboard board can be connected with a cellular module, wireless
aerials, the

CLSS Site Manager

, a configuration computer, a panel, a mobile device, and

an external power supply.

Figure 4.1

illustrates the connection options at the top side of the CLSS Gateway

mainboard board.

Figure 4.1: CLSS Gateway mainboard Connections - Top Side

Figure 4.2

illustrates the CLSS Gateway mainboard connection options at the bottom

side of the CLSS Gateway mainboard board.

Figure 4.2: CLSS Gateway mainboard Connection Options - Bottom Side

Fire Alarm Panel

CLSS
Cloud

Modbus
Client

Conﬁguration
Computer

Mobile
Connection

/NUP

Ethernet
Connection

WHITE COLOR

GREEN COLOR

RED COLOR

BLACK COLOR

BROWN COLOR

Future Use

UART/TTL

Future Use

(

Eth 1

)

(

Eth 0

)

Summary of Contents for CGW-MB




























































































































































































Search results

Summary of Contents for CGW-MB

Reviews:

Honeywell CGW-MB, Installation And User Manual, Page: 24 / 187

Search results

Summary of Contents for CGW-MB

Reviews: