manualshive.com logo in svg

Honeywell AUTOMATIC CONTROL, Engineering Manual

Honeywell AUTOMATIC CONTROL Engineering Manual is an essential resource for professionals seeking in-depth knowledge on control systems. This comprehensive manual covers various aspects of automatic control, providing valuable insights and practical guidance. Download your free copy exclusively from manualshive.com, the go-to hub for user manuals.

Share
Download
background image

ENGINEERING MANUAL OF AUTOMATIC CONTROL

CHILLER, BOILER, AND DISTRIBUTION SYSTEM CONTROL APPLICATIONS

379

INSTANTANEOUS CONVERTER CONTROL

An instantaneous converter is the standard type of converter

used in nearly all HTW heating installations because of its
extremely fast response. It is compact and available as standard
equipment.

The HTW flows through several passes of tubing within a

shell just large enough to accommodate the tube bundle.
Secondary water is supplied into the shell and surrounds the
tubes (Fig. 118). Only a small amount of HTW is needed to
heat a large volume of secondary water and the change is nearly
instantaneous. There is no room within the shell for a
temperature sensing element to quickly detect the change,
therefore, the temperature sensor must be located as close to
the converter as possible.

There must be a provision in the control loop to close the

HTW valve as soon as the secondary flow ceases. This requires
proving flow in case the flow stops for a reason other than the
pump is stopped by outdoor temperature, another signal, or
power failure. Even if the HTW valve closes as soon as
secondary water flow stops, flashing is likely to occur as there
is enough HTW in the tubes to overheat secondary water.
Flashing causes water hammer and possible equipment damage.
If shutdown is controlled, closing the HTW valve immediately
and delaying the secondary pump shutdown allows excess heat
in the converter to dissipate.

Fig. 118. Control of HTW to Constant

Temperature Hot Water Converter.

A constant temperature hot water supply is used where a

minimum temperature is required for all or part of the converter
load. Normally a converter for space heating does not require
fast response as the load changes only as fast as occupancy and
outdoor air conditions change. Because of the inherent fast
converter response there are several control requirements:

1. The primary sensing element must be located in outlet

water as close to the converter as possible.

2. A stainless steel well that matches the element with heat

conductive compound in the well must be used.

3. A primary control must be used that has integral action

and integral cutout to allow a wider throttling range for
stability with minimum deviation from setpoint and to
eliminate integral windup.

A control arrangement for a typical zone supplied with HW

from a HTW to constant temperature HW converter is shown
in Figure 119. Water temperature in the converter shell must be
reset from the outdoor air temperature for best control. Zones
typically are also reset from outdoor temperature.

Fig. 119. Typical Zone Control of Constant

Temperature HW from HTW Instantaneous Converter.

For modulating control, instantaneous converters must

operate with at least half design flow. To accomplish this, reset
schedules of controller C1 (Fig. 118) and C2 are arranged so
that valve V2 will be between half and full open to the converter
under normal conditions of operation. The reset schedule for
the converter is slightly higher than the temperature normally
required in the zones so that most of the water to supply the
needs of the zones must come from the converter rather than
the bypass.

C2 as the primary control prevents C3 from positioning V2

so the return water bypasses the converter. If flow is cut off
through the converter, the sensor located in the outlet piping
rather than within the shell cannot control V1 in a stable manner.

The use of an instantaneous converter (Fig. 120) for heating

water supplied directly to an air heating coil provides fast
response. Control system selection problems are the same as
for the control of a coil supplied with low or medium
temperature water except that a high quality valve with fast
control response is required for HTW.

C2934

OUTDOOR
AIR SENSOR

TO HTW
CONVERTER

ZONE
HIGH-LIMIT

INTERLOCKED
TO CLOSE
HTW VALVE 
WHEN
ALL PUMPS OFF

MANUAL
BALANCING VALVE

VALVE

V2

CONTROLLER

C2

CONTROLLER

C3

IMMERSION

SENSOR

LOAD

C2582

N.C.
VALVE

HTWR

HTWS

INSTANTANEOUS

CONVERTER

CONTROLLER

IMMERSION 

SENSOR

C1

RELAY

FLOW
SWITCH

PUMP

OFF
DELAY
TIMER

OUTDOOR 
AIR SENSOR

TO
ZONE(S)

Summary of Contents for AUTOMATIC CONTROL







































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AUTOMATIC CONTROL

Febco 860 Series Installation Instructions preview
860 Series
Brand: Febco Pages: 4
Cisco Catalyst 3110G Hardware Installation Manual preview
Catalyst 3110G
Brand: Cisco Pages: 48
NEC 78K0S/KA1+ Preliminary User'S Manual preview
78K0S/KA1+
Brand: NEC Pages: 304
FrSky Taranis Q X7S Manual preview
Taranis Q X7S
Brand: FrSky Pages: 2
GEA VARIVENT D Series Operating Instruction preview
VARIVENT D Series
Brand: GEA Pages: 78
GEA T-smart 7 Operating Instruction preview
T-smart 7
Brand: GEA Pages: 96
GEA T.VIS P-15 Operating Instruction preview
T.VIS P-15
Brand: GEA Pages: 66
UNI EV Series Operating And Mounting Manual preview
EV Series
Brand: UNI Pages: 21
OBSIDIAN CONTROL SYSTEMS NX4 Installation Manual preview
NX4
Brand: OBSIDIAN CONTROL SYSTEMS Pages: 13
Jabra 14201-20 - How To Connect preview
14201-20 -
Brand: Jabra Pages: 3
OBSIDIAN CONTROL SYSTEMS NX1 Installation Manual preview
NX1
Brand: OBSIDIAN CONTROL SYSTEMS Pages: 13
tau K125M Installation Manuals preview
K125M
Brand: tau Pages: 9
tau K100M Translation Of Original Instructions preview
K100M
Brand: tau Pages: 8
U-Prox IC L Installations preview
IC L
Brand: U-Prox Pages: 3
Watts 007 Series Installation, Maintenance & Repair preview
007 Series
Brand: Watts Pages: 4
Universal Remote Genesis MX-900 Manual preview
Genesis MX-900
Brand: Universal Remote Pages: 20
Jetter JetWeb JX2-PRN1 Operator'S Manual preview
JetWeb JX2-PRN1
Brand: Jetter Pages: 25
tell Compact-GSM Installation And Application Manual preview
Compact-GSM
Brand: tell Pages: 11

Brands by name

Popular brands

Load more brands