HOUSE
ID
DIP SWITCH POSITIONS
HOUSE
ID
DIP SWITCH POSITIONS
2
3
4
5
6
2
3
4
5
6
0
-
-
-
-
-
16
ON
-
-
-
-
1
-
-
-
-
ON
17
ON
-
-
-
ON
2
-
-
-
ON
-
18
ON
-
-
ON
-
3
-
-
-
ON
ON
19
ON
-
-
ON
ON
4
-
-
ON
-
-
20
ON
-
ON
-
-
5
-
-
ON
-
ON
21
ON
-
ON
-
ON
6
-
-
ON
ON
-
22
ON
-
ON
ON
-
7
-
-
ON
ON
ON
23
ON
-
ON
ON
ON
8
-
ON
-
-
-
24
ON
ON
-
-
-
9
-
ON
-
-
ON
25
ON
ON
-
-
ON
10
-
ON
-
ON
-
26
ON
ON
-
ON
-
11
-
ON
-
ON
ON
27
ON
ON
-
ON
ON
12
-
ON
ON
-
-
28
ON
ON
ON
-
-
13
-
ON
ON
-
ON
29
ON
ON
ON
-
ON
14
-
ON
ON
ON
-
30
ON
ON
ON
ON
-
15
-
ON
ON
ON
ON
31
ON
ON
ON
ON
ON
“ – “ indicates “OFF”
2
3
4
5
6
1
2-6 SETS HOUSE ID
SW-1
NOT USED
5800RL DIP Switch
5800RF-003-V0
OFF POSITION
INDICATOR
SV6
7L
Figure 4. DIP Switch Settings
RELAY and LED Operation
The 5800RL contains two relays (Figure 2) (SPDT, rated 2A.
28VAC/VDC) that may be used to activate remote sounders
and/or remote arm/disarm indicators. There are three LEDs
(green, yellow, red) located above the DIP switch and one
LED (red) located approximately in the center of the pc board.
The LEDs located above the DIP switch, indicate power and
relay activity. Refer to Figure 2 on the previous page. The RF
Interference LED monitors local radio frequency interference.
If this LED is continuously lit, the 5800RL should be
relocated.
Relay
LED
Activates Upon…
A
Yellow
Alarm conditions as follows:
Steady ON = burglary alarm (NO contact
connects to COM)
Temporal ON = fire alarm (NO contact connects
temporal to COM)
OFF = no alarms present (NC contact connects
to COM)
B
Red
System armed/disarmed as follows:
ON = system armed Away, Stay, or Instant (NO
contact connect to COM)
OFF = system disarmed (NC contact connects to
COM)
N/A
Green
Normally on (lighted) when power is applied.
Flickering indicates RF is being processed.
N/A
RF
Inter-
ference
Lights when RF activity is present.
If this LED is continuously lit, relocate the
5800RL module.
SPECIFICATIONS
Dimensions:
2-3/4”W x 4-15/16”H x 1-1/16”D
(70mm x 125mm x 27mm)
Voltage:
12VDC 100mA
or
9VAC, 15VA (use ADEMCO 1332 or equivalent)
Current:
100mA
Relay:
Two relays, each with choice of normally open (NO)
or normally closed (NC) operation.
Operating Temperature:
0 - 50°C / 32 - 122°F
Federal Communications Commission (FCC) Part 15
The user shall not make any changes or modifications to the equipment unless
authorized by the Installation Instructions or User's Manual. Unauthorized
changes or modifications could void the user's authority to operate the
equipment.
CLASS B DIGITAL DEVICE STATEMENT
This equipment has been tested to FCC requirements and has been found
acceptable for use. The FCC requires the following statement for your
information:
This equipment generates and uses radio frequency energy and if not installed
and used properly, that is, in strict accordance with the manufacturer's
instructions, may cause interference to radio and television reception. It has
been type tested and found to comply with the limits for a Class B computing
device in accordance with the specifications in Part 15 of FCC Rules, which are
designed to provide reasonable protection against such interference in a
residential installation. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause interference to
radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• If using an indoor antenna, have a quality outdoor antenna installed.
• Reorient the receiving antenna until interference is reduced or eliminated.
• Move the radio or television receiver away from the receiver/control.
• Move the antenna leads away from any wire runs to the receiver/control.
• Plug the receiver/control into a different outlet so that it and the radio or
television receiver are on different branch circuits.
• Consult the dealer or an experienced radio/TV technician for help.
INDUSTRY CANADA CLASS B STATEMENT
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
FCC/IC STATEMENT
This device complies with Part 15 of the FCC rules and RSS 210 of Industry
Canada. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesired
operation.
Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS 210
des Industries Canada. Son fonctionnement est soumis aux conditions
suivantes: (1) Cet appareil ne doit pas causer d' interférences nuisibles. (2) Cet
appareil doit accepter toute interférence reçue y compris les interférences
causant une réception indésirable.
ÊK37906Š
K3790 6/07 Rev. C
2 Corporate Center Drive, Melville, NY 11747
Copyright © 2007 Honeywell International Inc.
www.honeywell.com/security