Honeywell 60 Series Configuration Manual Download Page 79

Page: 79 / 93

Configuring System Settings

Configuring System Settings

This chapter contains the following sections:

•

Configuring System General Settings,

page 65

•

Configuring Maintenance Settings

, page 66

•

Configuring User Accounts Settings

, page 70

•

Configuring Access List Settings

, page 71

Configuring System General Settings

Go to

Setup



System Setup



General Settings

This section explains how to configure the basic settings for the camera, such as the host
name and system time.

Figure 8-1 Configuring System General Settings

Camera Name

: Enter a name for the camera. The text will be displayed at the top of the main

page.

Turn off the LED indicators

: If you do not want others to notice the network camera is in

operation, you can select this option to turn off the LED indicators.

Summary of Contents for 60 Series






























































































Search results

Summary of Contents for 60 Series

Reviews:

Related manuals for 60 Series

Brands by name

Popular brands

Honeywell 60 Series, Configuration Manual

Search results

Summary of Contents for 60 Series

Reviews:

Related manuals for 60 Series

Brands by name

Popular brands