Honeywell 104484A Product Data Download

Page: 1 / 16

PRODUCT DATA

68-0040-04

Immersion Wells and Compression Fittings

FOR TEMPERATURE CONTROLLERS

APPLICATION

Immersion wells, compression fittings and element holders

are used with Aquastat® Temperature Controllers to hold the

temperature sensing bulb in the controlled medium.

Immersion wells and compression fittings also prevent

leakage of the controlled medium.

FEATURES

• Immersion wells and compression fittings are

available to fit a 1/2-14 or 3/4-14 NPT tapping with

a range of insulation depths.

• Immersion wells and compression fittings are

available in a variety of lengths and diameters.

• Immersion wells and compression fittings are

available in a variety of materials, to suit the

application. Materials include: brass, copper,

stainless steel, mild steel or Monel.

• Element holders support the capillary and bulb

or an averaging element in duct applications.

• Bulb shields protect the sensing bulb from sun

and weather with the bulb installed outdoors.

• Accessories, including mounting clips, heat-

conductive compound, waste nuts, a pipe strap

and a well adapter, are available for mounting

sensing bulbs in various applications.

• Immersion wells allow heat transfer while

protecting the sensing bulb from contact with the

controlled medium.

• Immersion wells permit removal of the sensing

bulb for testing or replacement without draining

the system.

• Compression fittings seal the boiler and allow

bulb insertion directly into the controlled

medium.

IMMERSION WELL

112632AA

IMMERSION WELL

107324A

ELEMENT
HOLDER

104484A

COMPRESSION FITTING

121371B

Contents

Application ........................................................................

Features ...........................................................................

Specifications ...................................................................

Ordering Information ........................................................

General Information ..........................................................

Installation ........................................................................

Checkout .......................................................................... 13

Cross Reference .............................................................. 13

Summary of Contents for 104484A

















Search results

Summary of Contents for 104484A

Reviews:

Related manuals for 104484A

Brands by name

Popular brands

Honeywell 104484A, Product Data

Search results

Summary of Contents for 104484A

Reviews:

Related manuals for 104484A

Brands by name

Popular brands