Registering the Control with AlarmNet
Normally, registration with AlarmNet is done at the time the
control is installed. If the module is being installed as an add-
on, the control must be re-registered.
Follow the registration procedure in the control’s Installation
and Setup Guide. A summary of registration steps follows.
Register the control by using one of these methods:
Alpha Keypad using *29 Menu mode
1. Enter *29 Menu mode, select Diagnostic mode, then
use the [
↑
]
shift-B
command (D key followed by the
B key). The registration message is sent
(“Registering” displayed) and the control waits for the
acknowledgment.
2. “Registration SUCCESS” displayed, indicating
successful registration.
Test Switch on control’s PCB (triple-click)
1. Click the switch three times.
2. Watch the Status LEDs: The Message (yellow) LED
and the Status (green) LED will blink slowly in unison
while registration is in progress.
3. When registration is complete, the Status (green)
LED goes out.
AlarmNet 360 website
See paragraph at right.
By phone
1. Call 1-800-222-6525
You will need the following information:
•
MAC ID and MAC CRC number (found on the label
on control’s PC board).
•
Subscriber information (provided by the central
station), including a city code, CSID, and a
subscriber ID.
•
Activation ID (AID) and AID CRC numbers (found on
the label on the module or on its carton)
2. When instructed to do so, triple-click the Test switch
to complete the registration.
Registering through AlarmNet Direct Website
To register via AlarmNet 360 Website, please go to:
www.alarmnet360.com
Log in and follow the on-screen prompts.
Please have the following information available:
•
Primary City ID (two-digit number provided by central station)
•
Primary Central Station ID (two-digit hexadecimal number provided by
central station)
•
Primary Subscriber ID (four-digit number provided by central station)
•
MAC ID and MAC CRC number (located on outside of box and on
label on control’s PC board)
•
AID and AID CRC numbers (found on the label on the module or on its
carton).
Once the control is registered, you may log out of the AlarmNet 360
website.
FCC / IC STATEMENT
The user shall not make any changes or modifications to the equipment
unless authorized by the Installation Instructions or User's Manual.
Unauthorized changes or modifications could void the user's authority to
operate the equipment.
CLASS B DIGITAL DEVICE STATEMENT
This equipment has been tested and found to comply with the limits for a
Class B digital device, as defined by FCC Rules Part 15.105. The Class B
Digital Device statement can be viewed at:
https://customer.resideo.com/en-US/support/residential/codes-and-
standards/FCC15105/Pages/default.aspx
This device complies with Part 15 of the FCC Rules, and RSS210 of Industry
Canada. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesired
operation.
Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS 210
des Industries Canada. Son fonctionnement est soumis aux conditions
suivantes: (1) Cet appareil ne doit pas causer d’interférences nuisibles. (2)
Cet appareil doit accepter toute interférence reçue y compris les interférences
causant une réception indésirable.
Responsible Party / Issuer of
Supplier’s Declaration of Conformity:
Ademco Inc., a subsidiary of Resideo
Technologies, Inc., 2 Corporate
Center Drive., Melville, NY 11747,
Ph: 516-577-2000
Partie responsable / Émetteur de la
déclaration de conformité du
fournisseur :
Ademco Inc., une filiale
de Resideo Technologies, Inc., 2
Corporate Center Drive., Melville, NY
11747, Tél. 516 577-2000
ANTENNA SPECIFICATIONS
Type:
Broadband External LTE/Cellular
Antenna
VSWR:
<2.5:1
Polarization:
Vertical
Impedance:
50 Ohms
Gain (Peak):
1.18dBi ~ 4.0dBi
Connector Type:
SMA male
Current Drain (measured at the Vista-
21iPLTE AC input):
60mA average standby,
580mA (rms) peak transmit
Frequency Bands
LTE
Band 2
LTE
Band 4
LTE
Band 5
LTE
Band 12
LTE
Band 13
WCDMA
Band II
WCDMA
Band V
LTE-21V
X
X
X
X
X
X
X
IMPORTANT NOTE ABOUT EXTERNAL ANTENNAS
Antenna may only be installed or replaced ONLY by a professional installer.
TO THE INSTALLER
The external antenna gain shall not exceed 6.94 dBi for 700 MHz and 850MHz, 6.00 dBi for 1700 MHz, and 9.01 dBi for 1900 MHz. Under no conditions may an
antenna gain be used that would exceed the ERP and EIRP power limits as specified in FCC Parts 22H, 24E and 27
.
SUPPORT, WARRANTY, & PATENT INFORMATION
For the latest documentation and online support information, please go to:
https://mywebtech.honeywellhome.com/
For the latest warranty information, please go to:
https://www.security.honeywellhome.com/hsc/resources/wa/index.html
For patent information, see https://www.resideo.com/patent
MyWebTech
Warranty
Patents
The product should not be disposed of with other household waste. Check for the nearest
authorized collection centers or authorized recyclers. The correct disposal of end-of-life
equipment will help prevent potential negative consequences for the environment and human
health.
This product is manufactured by Resideo Technologies, Inc. The Honeywell Home
Trademark is used under license from Honeywell International Inc.
Ê800-25357CÆŠ
800-25357C 3/19 Rev C
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
2019 Resideo Technologies, Inc.
www.resideo.com