Honda VFR1200F Owner'S Manual Download Page 28

Page: 28 / 143

Operation Guide

Indicators

Low oil pressure indicator

Comes on when the ignition switch is turned ON.
Goes off when the engine starts.

If it comes ON while engine is running:

P.91

PGM-FI (Programmed Fuel Injection)

malfunction indicator lamp (MIL)

Comes on briefly when the ignition switch is turned ON
with the engine stop switch in the RUN

position.

If it comes ON while engine is running:

P.91

ABS (Anti-lock Brake

System) indicator

Comes on when the ignition
switch is turned ON. Goes off
when your speed reaches
approximately 6 mph (10 km/h).

If it comes ON while riding:

P.92

High coolant

temperature indicator

If it comes ON while riding:

P.90

Parking brake indicator

(VFR1200FD only)

Lights as a reminder that you
have not released the parking
brake lever.

P.33

31MGE601.indb 26

2010/03/08 18:05:26

Summary of Contents for VFR1200F
















































































































































Search results

Summary of Contents for VFR1200F

Reviews:

Related manuals for VFR1200F

Brands by name

Popular brands

Honda VFR1200F, Owner'S Manual

Search results

Summary of Contents for VFR1200F

Reviews:

Related manuals for VFR1200F

Brands by name

Popular brands