Honda Super Cub 2019 Manual Download Page 117

Page: 117 / 153

Rear Wheel

Removal

Support your motorcycle securely and

raise the rear wheel off the ground using

the center stand or a hoist.

Remove the chain covers.

P. 92

Remove the rear brake adjusting nut.

Disconnect the brake rod from the brake

arm.

Disconnect the brake stopper arm from

the brake panel by removing the cotter

pin, brake stopper arm nut, washer and

rubber grommet.

Remove the rear axle nut and washer,

then loosen the drive chain lock nuts and

drive chain adjusting nuts.

Remove the rear axle shaft, chain

adjusting plates and side collars, then

remove the drive chain from the driven

sprocket by pushing the rear wheel

forward.

Remove the rear wheel from the

swingarm.

20181019183311_31K0GA000_enu_BOOK Page 118 Friday, October 19 2018 18:39:26 JST

Tire Puncture

Removing Wheels

Troubleshooting

115

Continued

Drive chain

adjusting nut

Brake stopper arm nut

Drive chain

lock nut

Brake

arm

Rear brake adjusting nut

Brake

stopper

arm

Cotter

pin

Brake rod

Rear axle nut/Washer

Adjusting plate

Summary of Contents for Super Cub 2019


























































































































































Search results

Summary of Contents for Super Cub 2019

Reviews:

Related manuals for Super Cub 2019

Brands by name

Popular brands

Honda Super Cub 2019, Manual

Search results

Summary of Contents for Super Cub 2019

Reviews:

Related manuals for Super Cub 2019

Brands by name

Popular brands