Honda Miimo HRM310 Owner'S Manual Download

Page: 71 / 88

7 MAINTENANCE

Maintenance procedures

Replacing the blades

To replace the blades, perform the procedures below.

WARNING

- Put on a pair of work gloves before performing the following procedures.
- Do not touch the blade while it is spinning. You may be injured if you do so.

NOTE:

- This work requires technical skill and knowledge, as well as special tools. Consult your dealer if you cannot

perform the procedures below.

- Before replacing the blades, remove the grass clippings (

page 64) .

- Use genuine parts or their equivalent for the blade.

Turn the power off.
Adjust the height of the blades to position 1 and
turn the lawn mower upside down.

Hold the base of the blade disc with a 15/16 in
(24 mm) wrench so that the blade disc does not
rotate when you rotate the nuts.

Remove the nut from each blade with a 5/16 in
(8 mm) wrench.

Replace the blades, insert each blade through
each bolt on the blade disc, and lightly tighten a
nut with a 5/16 in (8 mm) wrench.

NOTE:

- Tighten the nuts after the shoulders of the nut

is securely in the hole of the blade.

Tighten the nuts to the speci

ed torque value

using a torque wrench.

3.2~4.4 lbf • ft (4.4~6.0 N • m, 0.45~0.60 kgf • m)

NOTE:

- If you do not have a torque wrench, have your

dealer perform the work.

- Use a wrench between the blade disc and the

lawn mower body.

Check that the blades rotate smoothly. If they do
not rotate smoothly, remove and install the nuts
again.

Hold the blade disc in place

Insert a wrench between the blade
disc holder and the lawn mower
body.

Nut

Thread

Correct

Incorrect

Shoulder
of nut

Blade

Blade disc

Summary of Contents for Miimo HRM310

























































































Search results

Summary of Contents for Miimo HRM310

Reviews:

Related manuals for Miimo HRM310

Brands by name

Popular brands

Honda Miimo HRM310, Owner'S Manual

Search results

Summary of Contents for Miimo HRM310

Reviews:

Related manuals for Miimo HRM310

Brands by name

Popular brands