manualshive.com logo in svg

Honda Metropolitan CHF50, Service Manual, Page: 269 / 319

Share
Download
Honda Metropolitan CHF50 Service Manual Download Page 269

IGNITION SYSTEM

16-7

If the peak voltage measured at the ECM connector

is abnormal, measure the peak voltage at the pulse

generator connector.
Disconnect  the  alternator/starter  6P  (W)  connector

and  connect  the  peak  voltage  tester  or  adaptor

probes to the connector terminals of the alternator/

starter side.

In the same manner as at the ECM connector, mea-

sure the peak voltage and compare it to the voltage

measured at the ECM connector.

 

•

If  the  peak  voltage  measured  at  the  ECM  is

abnormal  and  the  one  measured  at  the  alterna-

tor/starter  is  normal,  the  wire  harness  has  an

open or short circuit, or loose connection.

 

•

If the peak voltage is lower than standard value,

follow the checks described in the troubleshoot-

ing chart (page 16-4).

Install  the  removed  parts  in  the  reverse  order  of

removal.

IGNITION COIL

REMOVAL/INSTALLATION

Remove the luggage box (page 2-6). 
Disconnect the spark plug cap from the plug.

Disconnect  the  ignition  coil  primary  wire  connec-

tors.

Remove the bolt and ignition coil.
Installation is in the reverse order of removal.

6P (W) CONNECTOR

6P (W) CONNECTOR

BOLT

IGNITION COIL

CONNECTORS

Summary of Contents for Metropolitan CHF50
































































































































































































































































































































Reviews:

No comments