background image

12

Blade Inspection

1. Turn the fuel valve OFF (

page 3

).

2. Disconnect the spark plug cap from the spark plug (

page 14

).

3. Tilt the mower to the right side so that the fuel cap side is up. This 

will help to prevent fuel leakage and hard starting due to carburetor 
flooding.

4. Inspect the blades for damage, cracks, and excessive rust or 

corrosion.

A dull blade can be sharpened, but a blade that is excessively worn, 
bent, cracked, heavily rusted, or otherwise damaged must be 
replaced.

If a blade is bent, take the lawn mower to an authorized Honda 
servicing dealer for inspection.

Blade Mounting Bolt Inspection

Inspect the blade bolts for any signs of damage 
or looseness. If they are damaged, they must 
be replaced.

If they appear loose, a torque wrench must be 
used to accurately tighten the blade bolts to the 
required torque. If you do not have a torque 
wrench, take your lawn mower to an authorized 
dealer to have the bolts replaced or tightened.

Use only Honda Genuine blade bolts and 
special washers, since they are specifically 
designed for this purpose. Replacement part 
numbers are on 

page 20

.

Blade Replacement

1. Turn the fuel valve OFF (

page 3

).

2. Disconnect the spark plug cap from the spark plug (

page 14

).

3. Tilt the mower to the right side so that the fuel cap side is up. This 

will help to prevent fuel leakage and hard starting due to carburetor 
flooding.

4. Remove the two blade bolts with a 14 mm (6 point) socket wrench. 

Use a wooden block to prevent the blades from turning when 
removing the bolts. Remove the blades.

5.  Clean dirt and grass from around the blade mounting area.

6. Install the sharpened or replacement blades using the two blade 

bolts and special washers as shown below. Be sure to install the 
washers in the direction shown.

Always install both blades as a set.

The blade bolts and washers are specially designed for this 
application. When replacing bolts and washers, use only Honda 
Genuine replacement parts.

7. Tighten the blade bolts with a torque wrench to the specified 

torque. Use a wooden block to prevent the blades from turning 
when tightening the bolts, as shown on 

page 13

.

Blade bolt torque: 

36 ~ 43 ft-lb (49 ~ 59 N·m)

If you do not have a torque wrench, have an authorized Honda 
servicing dealer tighten the blade bolts.

 WARNING

A worn, cracked, or damaged blade can break, and 
pieces of the damaged blade can become dangerous 
projectiles.

Blades thrown from the mower could seriously hurt or kill 
someone.

Inspect the blades regularly, and do not operate the 
mower with worn or damaged blades.

BLADE BOLTS

BLADES

NORMAL

WORN

BENT

CRACKED

NORMAL 

TRAILING EDGE

EXCESSIVELY 

WORN TRAILING 

EDGE

Inspect washers and 

bolt heads for 

looseness and 

damage.

 WARNING

Operating the mower with only one blade will result in an 
improperly seated blade that can become dangerous 
projectiles. 

Blades thrown from the mower could seriously hurt or kill 

someone.

Always install both blades as a set.

UPPER BLADE

LOWER 
BLADE

BLADE 
BOLT (2)

SPECIAL WASHER (2)

BLADE BOLT [2] 

AND WASHER [2]

SPECIAL WASHER 
DIRECTION

UPPER BLADE

LOWER BLADE

Summary of Contents for HRX217VKAA

























Reviews: