background image

28

AVOIDING FUEL-RELATED PROBLEMS

When maintained properly, your Honda trimmer should provide years of trouble-free operation. This includes the fuel system. However, 
gasoline can quickly deteriorate, causing starting or running problems and, in some cases, damage to the fuel system. Most fuel-related 
problems can be avoided by following the precautions listed below. Fuel system damage and engine performance problems resulting from 
deteriorated fuel are not covered by the 

Distributor’s Limited Warranty

 (see 

page 30

).

Follow These Precautions to Prevent Most Fuel-Related Problems

During The Normal Trimming Season

Reason

Do not use gasoline containing more than 10% ethanol.

A high level of ethanol in gasoline attracts water and can corrode 
or damage the fuel system and cause performance problems.

Store gasoline in a clean, plastic, sealed container approved for 
fuel storage. 

Store your fuel supply container away from direct sunlight; if the 
container has a vent, keep it closed.

A clean plastic container will prevent rust and metallic 
contaminants from entering the fuel system.

Gasoline will deteriorate faster when exposed to air and sunlight.

Purchase only enough gasoline to last for 30 to 60 days.

If you purchase enough gasoline to last for more than 60 days, 
add a fuel stabilizer to your storage tank when you fill it.

Gasoline deteriorates with age, so try to avoid storing it for long 
periods, especially in summer heat.

Fuel stabilizer will extend the shelf life of gasoline, but it will not 
reconstitute stale fuel.

When you finish trimming, completely fill the trimmer’s fuel tank.

If the fuel tank is only partially filled, air in the tank will promote 
fuel deterioration.

3 to 4 Weeks Before Next Use

Reason

Completely fill the trimmer’s fuel tank.

If the fuel tank is only partially filled, air in the tank will promote 
fuel deterioration.

1 to 3 Months Before Next Use

Reason

If you did not add fuel stabilizer to your fuel storage tank when 
you filled it up, fill your trimmer’s fuel tank with fresh gasoline. 

If the fuel tank is only partially filled, air in the tank will promote 
fuel deterioration.

Add fuel stabilizer to the trimmer’s tank according to the stabilizer 
manufacturer’s instructions.

Fuel stabilizer will extend the life of gasoline, but it will not 
reconstitute stale gasoline.

Run the engine outdoors for 10 minutes.

To make sure treated gasoline has replaced untreated gasoline 
throughout the fuel system.

More Than 3 Months Before Next Use

Reason

Drain the fuel tank into an approved container and then run the 
engine until the engine stops. Do not allow gasoline to remain in 
your trimmer for more than 3 months of inactivity.

All fuel stabilizers have a shelf life. It is good practice to empty 
the fuel system for long term inactivity.

We recommend Pro Honda Fuel Stabilizer, that has improved formulation with added corrosion protection (

page 29

).

Summary of Contents for HHT25S





































Reviews: