Honda Harmony II HRR216K1PDA Owner'S Manual Download

Page: 49 / 66

TRANSMISSION

S3D

Type

single speed

3-speed

Ground Speeds

2.8 mph (4.5 km/h)

1st: 1.8 mph (2.9

km/h)

2nd: 2.7 mph (4.3

km/h)

3rd: 3.4 mph (5.4

km/h)

MAINTENANCE

Fuel

Unleaded gasoline with a pump
octane rating of 86 or higher

See page 37.

Engine Oil

SAE 10W-30, API SH or SJ

See page 34.

Transmission lubricant (SD)

Grease (NLGI #2)

See shop manual.

Spark Plug Type

(Resistor plugs reduce
interference with radio and
television reception.)

Regular:
NGK – BP6ES
DENSO – W20EP-U
Resistor:
NGK - BPR6ES
DENSO - W20EPS-U

See page 36.

Maximum Governed Speed

3,100 +0/-150 rpm

See shop manual.

Throttle Cable

Adjust for proper choke
operation and maximum
governed speed.

See shop manual.

Blade Bolt Torque

36 ~ 43 ft-lb
(5.0 ~ 6.0 kg-m, 49 ~ 59 N

•

See page 38.

TUNEUP

Spark Plug Gap

0.028 ~ 0.031 in (0.7 ~ 0.8 mm)

See page 36.

Idle Speed

1,700

150 rpm

See shop manual.

Valve Clearance (cold)

Intake:

0.15

0.02 mm

Exhaust: 0.20

0.02 mm

See shop manual.

Other Specifications

No other adjustments needed.

SPECIFICATIONS

Summary of Contents for Harmony II HRR216K1PDA



































































Search results

Summary of Contents for Harmony II HRR216K1PDA

Reviews:

Related manuals for Harmony II HRR216K1PDA

Brands by name

Popular brands

Honda Harmony II HRR216K1PDA, Owner'S Manual

Search results

Summary of Contents for Harmony II HRR216K1PDA

Reviews:

Related manuals for Harmony II HRR216K1PDA

Brands by name

Popular brands