background image

MAINTENANCE

3-10

COMBUSTION CHAMBER CLEANING

Remove the cylinder (page 14-2).
Prepare a cylinder of a thick paper or equivalent

material (1), which diameter is as large as to fit against

the inner wall of the cylinder, and insert the paper into

the cylinder.
Attach the cleaning brush (special tool) (2) to an electric

drill and clean any carbon deposits from the combustion

chamber.

 • Do not remove valves from the cylinder while

cleaning the combustion chamber.

 • Be sure to insert a thick paper into the cylinder to

protect the inner wall of the cylinder during clearing

of the combustion chamber.

 • Do not press the cleaning brush with force against

the combustion chamber.

FUEL FILTER REPLACEMENT

Check the fuel filter (1) for water accumulation or

sediment. If necessary replace it.

Install the commercially available tube clamps (1) on

the fuel tubes (2) on both sides of the fuel filter (3).
Disconnect the fuel tube from the fuel filter to remove

the fuel filter.
Install a new fuel filter with the arrow mark toward the

carburetor side.
Check the connecting parts for any sign of fuel leakage.

TOOL:
Cleaning brush (2)

07998-VA20100

(1)

(2)

Gasoline is highly flammable and explosive.

You can be burned or seriously injured when han-

dling fuel.

 • Keep heat, sparks and flame away.

 • Handle fuel only outdoors.

 • Wipe up spills immediately.

(1)

(2)

(1)

(3)

(2)

62Z6N000.book  10 ページ  2009年6月16日 火曜日 午後6時17分

Summary of Contents for GX630











































Reviews: