FUEL SYSTEM
6-6
CARBURETOR DISASSEMBLY/
ASSEMBLY
Before disassembly, clean the outside of the carburetor.
Gasoline is highly flammable and explosive.You
can be burned or seriously injured when handling
fuel.
• Keep heat, sparks and flame away.
• Handle fuel only outdoors.
• Wipe up spills immediately.
To prevent serious eye injury, always wear safety
goggles or other eye protection when using com-
pressed air.
ASSEMBLY:
Before installing, clean
thoroughly with low
compressed air (207 kPa
(2.11 kgf/cm
2
, 30 psi) or
less).
ASSEMBLY:
Set the float (1) and float pin (2)
to the carburetor body (3).
Tighten the stop screw (4) to
secure the float pin as shown.
FUEL STRAINER
SCREEN
MAIN JET
FLOAT
PIN
O-RING
DRAIN
SCREW
FUEL CUT SOLENOID
STOP SCREW
(4)
(2)
FLOAT
VALVE
(1)
(3)
PILOT JET
PLATE
FROAT CHAMBER
FLOAT
PILOT SCREW
ASSEMBLY:
Before installing, clean thoroughly
with low compressed air (207 kPa
(2.11 kgf/cm
2
, 30 psi) or less).
Lightly lubricate the O-ring (1) to
ensure easy installation into the
carburetor body.
(1)
SCREW (4)
SCREW
SEALING WASHER
MAIN NOZZLE
MAIN JET NUMBER:
GX630/GX630R:
L side (No.1 CYLINDER) #102
R side (No.2 CYLINDER) #105
GX660/GX660R: #112
GX690/GX690R: #118
ASSEMBLY:
Before installing, clean
thoroughly with low
compressed air (207
kPa (2.11 kgf/cm2, 30
psi) or less).
MAIN JET
NUMBER
8.8 N·m (0.90 kgf·m,
6.5 lbf·ft)
L SIDE MARK
R SIDE MARK
TUBE CLIP B8
DRAIN TUBE
<0DQQMࡍࠫ㧞㧜㧜㧥ᐕ㧢㧝㧢ᣣޓἫᦐᣣޓඦᓟ㧢ᤨ㧝㧣ಽ
Summary of Contents for GX630
