Honda Forza 750 2020 Manual Download

Page: 112 / 211

Refuelling

Fuel type:

Unleaded petrol only

Fuel octane number:

Your vehicle is

designed to use Research Octane Number

(RON) 91 or higher.

Tank capacity:

13.2 L (3.49 US gal, 2.90 Imp

gal)

Refuelling and Fuel Guidelines

(

P.15

)

Opening the Fuel Fill Cap

Make sure that the Honda SMART Key is

activated

(

P.82

)

and enter the operating

range for the vehicle.

(

P.83

)

Push the fuel lid opener switch.

Turn the fuel fill cap counterclockwise until it

stops and remove the cap.

Do not fill with fuel above the lower edge of

the filler neck.

20201009081441_32MKV6000_eng_BOOK Page 112 Friday, October 09 2020 08:19:30 JST

Operation Guide

109

Continued

Fuel lid

opener switch

Lower edge

of filler neck

Fuel fill cap

Fuel lid

Arrow marks

Summary of Contents for Forza 750 2020




















































































































































































































Search results

Summary of Contents for Forza 750 2020

Reviews:

Related manuals for Forza 750 2020

Brands by name

Popular brands

Honda Forza 750 2020, Manual

Search results

Summary of Contents for Forza 750 2020

Reviews:

Related manuals for Forza 750 2020

Brands by name

Popular brands