Honda F220 Owner'S Manual Download Page 21 | Manualshive

Page: 21 / 60

background image

19

OPERATION

HONDA F220 (E) 00X31-V14-6120 -

OPERATING THE CONTROLS FOR TILLING

If the tines dig in but the machine will not move forward, move the handlebars
from side-to-side. When turning, push down on the handlebars to bring the
tiller’s weight to the rear; this will make turning easier.

Handlebar Height Adjustment

Stop the engine before adjusting
the handlebar height.

To adjust the handlebar height,
loosen the handlebar height
adjuster, select the appropriate
holes and tighten it.

Clutch

When the main clutch lever is
squeezed, the clutch is engaged,
and power is transmitted to the
transmission.

When the lever is released, the
clutch is disengaged, and power
is not transmitted.

HANDLEBAR
HEIGHT
ADJUSTER

MAIN CLUTCH
LEVER

F220_EN.book 19 ページ２０１０年２月１２日　金曜日　午前１１時２分

«
...
19
20
21
22
23
...
»

Summary of Contents for F220





























































Reviews:

No comments

Related manuals for F220

Brand: Data Aire Pages: 24

Brand: Craftsman Pages: 69

Brand: Craftsman Pages: 20

Brand: Troy-Bilt Pages: 19

634B-Super Bronco

Brand: Troy-Bilt Pages: 32

Brand: DR Pages: 54

Brand: Stirling Pages: 20

Brand: Carrier Pages: 26

Brand: ILVE Pages: 24

Brand: Yard Machines Pages: 20

Brand: Yardworks Pages: 22

Brand: hailea Pages: 16

Brand: Land Pride Pages: 18

Brand: Craftsman Pages: 24

3.75 HP 17 INCH TINE WIDTH 917.2922

Brand: Craftsman Pages: 32

Brand: Craftsman Pages: 64

Brand: red roo Pages: 20

Brand: York Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands