Honda EU3200i Owner'S Manual Download | Manualshive

Page: 65 / 100

background image

STORAGE

63

DRAINING THE FUEL TANK

Unscrew the fuel filler cap (see page 16), remove the fuel strainer, and empty the
fuel tank into an approved gasoline container. We recommend using a
commercially available gasoline hand pump to empty the tank. Do not use an
electric pump. Siphon the gasoline by inserting the tip of the hand pump into
the side of the pump guard, as shown in the figure below. Reinstall the fuel
strainer and the fuel filler cap.

Gasoline is highly flammable and
explosive.

You can be burned or seriously injured
when handling fuel.

• Stop the engine and let it cool before

handling fuel.

• Keep heat, sparks, and flame away.
• Handle fuel only outdoors.
• Keep away from your vehicle.
• Wipe up spills immediately.

FUEL STRAINER

PUMP GUARD

HAND PUMP

«
...
63
64
65
66
67
...
»

Summary of Contents for EU3200i





































































































Reviews:

No comments

Related manuals for EU3200i

Brand: ICS Pages: 26

Brand: GENERGY Pages: 90

Brand: Laser Pages: 9

Brand: Sangean Pages: 1

Brand: SMC Networks Pages: 40

DIGITRADIO 230 OD

Brand: TechniSat Pages: 644

Brand: Briggs & Stratton Pages: 8

WEDECO SMOevo PLUS Series

Brand: Xylem Pages: 179

TOWER LIGHT CUBE+ HYBRID

Brand: Generac Power Systems Pages: 74

Brand: Caliber Pages: 18

Brand: Parkside Pages: 120

Brand: I.SOUND Pages: 16

Brand: ION Pages: 33

Brand: Winco Pages: 18

Brand: Philips Pages: 2

Brand: Philips Pages: 3

Brand: Laser Pages: 20

Brand: Mitsubishi Pages: 136

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands