Honda EU3200i Owner'S Manual Download

Page: 36 / 100

BEFORE OPERATION

ENGINE OIL LEVEL CHECK

Check the engine oil level with the generator on a level surface and the engine
stopped.

1. Loosen the maintenance cover screw and remove the maintenance cover.

2. Remove the oil filler cap by turning it counterclockwise. Wipe the dipstick

clean.

3. Insert the dipstick into the oil filler neck as shown, but do not screw it in, then

remove it to check the oil level.

4. If the oil level is near or below the lower limit, fill with the recommended oil

to the upper limit. Do not overfill.

• “Upper limit” means the oil exists to the oil filler neck.
• “Lower limit” means the oil is attached only to the lower end of the

dipstick.

Refer to "ENGINE OIL RECOMMENDATIONS" in page 14.

5. Reinstall the oil filler cap securely.

6. Reinstall the maintenance cover and tighten the maintenance cover screw

securely.

MAINTENANCE COVER

MAINTENANCE COVER SCREW

OIL FILLER NECK

UPPER LIMIT
(The oil exists to
the oil filler neck.)

OIL FILLER CAP

LOWER LIMIT
(The oil is attached
only to the lower
end of the dipstick.)

DIPSTICK

Summary of Contents for EU3200i





































































































Search results

Summary of Contents for EU3200i

Reviews:

Related manuals for EU3200i

Brands by name

Popular brands

Honda EU3200i, Owner'S Manual

Search results

Summary of Contents for EU3200i

Reviews:

Related manuals for EU3200i

Brands by name

Popular brands