background image

BEFORE OPERATION

33

To prevent a possible fire, keep the generator at least 3 feet (1 meter) away from 
building walls, vehicles, and other equipment during operation. Do not place 
flammable objects close to the engine or exhaust.

Before beginning your pre-operation checks, be sure the generator is on a level 
and firm surface and the engine switch is in the OFF position.

Check the Engine

• Before each use, look around and underneath the engine for signs of oil or 

gasoline leaks.

• Check the engine oil level (see page 34). A low engine oil level will cause the 

Oil Alert system to shut down the engine.

• Check the air filters (see page 35). Dirty air filters will restrict air flow to the fuel 

system, reducing engine and generator performance.

• Check the fuel level (see page 15). Starting with a full tank will help to 

eliminate or reduce operating interruptions for refueling.

AC Appliance and Power Cord

Before connecting an AC appliance or power cord to the generator:

• Use grounded 3-prong extension cords, tools, and appliances, or double-

insulated tools and appliances.

• Inspect cords and plugs, and replace if damaged.

• Make sure that the appliance is in good working order. Faulty appliances or 

power cords can create a potential for electric shock.

• Make sure the electrical rating of the tool or appliance does not exceed the 

rated power of the generator or the receptacle being used.

• Do not exceed the current limit specified for any one receptacle.

Summary of Contents for EU3200i





































































































Reviews: