Honda EU2200i Owner'S Manual Download Page 24 | Manualshive

Page: 24 / 104

background image

CONTROLS & FEATURES

22

Fuel Filler Cap Vent Lever

The fuel filler cap is provided with a vent lever to seal the fuel tank.

The vent lever must be in the ON position for the engine to run.

When the engine is not in use, leave the vent lever in the OFF position to reduce
the possibility of fuel leakage. Allow the engine to cool well before turning the
vent lever to the OFF position.

Choke Lever

The choke is used to provide proper starting mixture when the engine is cold. It
can be opened and closed by operating the choke lever manually. Move the
choke lever to the CLOSED position to enrich the mixture for cold starting.

FUEL FILLER CAP VENT LEVER

OFF

ON

FUEL FILLER CAP

OPEN

CHOKE LEVER

CLOSED

31Z446100.book 22 ページ２０２０年２月１７日　月曜日　午前１１時４１分

«
...
22
23
24
25
26
...
»

Summary of Contents for EU2200i









































































































Reviews:

No comments

Related manuals for EU2200i

HDG3000B Series

Brand: Hantek Pages: 22

Brand: CARLO GAVAZZI Pages: 32

Brand: Powermate Pages: 12

Brand: GPX Pages: 16

MSX+ 152/120 48F SBM-485

Brand: phytron Pages: 66

Brand: MULTIQUIP Pages: 72

Music Angel 12022

Brand: QooPro Pages: 4

Brand: e-Storm Pages: 11

Brand: E.F. Johnson Pages: 86

Brand: Sportsman Pages: 30

Brand: SSI Pages: 12

Brand: Yaesu Pages: 60

Brand: Buffalo Tools Pages: 22

Sportsman GEN4K

Brand: Buffalo Tools Pages: 38

Brand: Sunstech Pages: 67

Brand: Krüger & Matz Pages: 64

Brand: gofanco Pages: 12

Brand: Aiwa Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands