Honda EU 1000i Owner'S Manual Download | Manualshive

Page: 45 / 92

background image

43

SERVICING YOUR GENERATOR

REFUELING

FUEL TANK CAP

UPPER LEVEL MARK

Gasoline is highly flammable and
explosive.

You can be burned or seriously
injured when handling fuel.

Stop the engine and keep heat,
sparks, and flame away.
Handle fuel only outdoors.
Wipe up spills immediately.

Fuel can damage paint and plastic. Be careful not to spill fuel when
filling your fuel tank. Damage caused by spilled fuel is not covered
under warranty.

Refuel in a well-ventilated area before starting the engine. If the engine
has been running, allow it to cool. Refuel carefully to avoid spilling fuel.

Never refuel the engine inside a building where gasoline fumes may
reach flames or sparks. Keep gasoline away from appliance pilot lights,
barbecues, electric appliances, power tools, etc.
Spilled fuel is not only a fire hazard, it causes environmental damage.
Wipe up spills immediately.

With the engine stopped, remove the fuel tank cap and check the fuel
level. Refill the fuel tank if the fuel level is low.

Do not fill above the upper level mark.

After refueling, reinstall the fuel tank cap securely.

10/03/11 13:00:30 31ZT3620_044

«
...
43
44
45
46
47
...
»

Summary of Contents for EU 1000i





























































































Reviews:

No comments

Related manuals for EU 1000i

IMAGEPRESS C7010VPS

Brand: Canon Pages: 4

Brand: Wallenstein Pages: 31

Brand: Quincy lab Pages: 4

Brand: Farenheit Pages: 8

Brand: Manfrotto Pages: 2

Brand: Manfrotto Pages: 2

Brand: Mammut Pages: 32

Brand: Vello Pages: 30

Brand: X Rocker Pages: 12

Brand: YachtSafe Pages: 2

Brand: Rice Lake Pages: 2

Brand: Olympus Pages: 172

Brand: Uniden Pages: 8

Brand: Magicshine Pages: 2

Power Commander III 718-411

Brand: Dynojet Pages: 3

Brand: DMP Electronics Pages: 4

THINKPAD A30P -

Brand: IBM Pages: 88

DSE-LFP51.2V50A-16sLFP36115185-50A-PB50-MC-CO07-M21A

Brand: MOTOMA Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands