Honda EB5000i Owner'S Manual Download | Manualshive

Page: 50 / 96

background image

48

SERVICING YOUR GENERATOR

ENGINE OIL CHANGE

UPPER LIMIT

OIL DRAIN PLUG

OIL FILLER CAP/DIPSTICK

SEALING
WASHER

OIL FILLER
CAP/DIPSTICK

Drain the oil while the engine is warm to assure rapid and complete
draining.

Place a suitable container below the engine to catch the used oil,
then remove the oil filler cap/dipstick, drain plug and sealing washer.

Allow the used oil to drain completely, then reinstall the drain plug
and sealing washer. Tighten the plug securely.

Improper disposal of engine oil can be harmful to the environment.
If you change your own oil, please dispose of the used oil properly.
Put it in a sealed container and take it to a recycling center. Do not
discard it in a trash bin, dump it on the ground or pour it down the
drain.

With the generator in a level position, fill to the outer edge of the oil
filter hole with the recommended oil (see page

Screw in the oil filler cap/dipstick securely.

Wash your hands with soap and water after handling used oil.

1.

2.

3.

4.

04/09/30 11:59:21 31Z12600_049

«
...
48
49
50
51
52
...
»

Summary of Contents for EB5000i

































































































Reviews:

No comments

Related manuals for EB5000i

Brand: LENCO Pages: 66

Brand: Ultimate Ears Pages: 2

Brand: K&S BASIC Pages: 13

Brand: Sytech Pages: 4

Brand: Caliber Pages: 18

Brand: Sandstrom Pages: 140

Brand: Edwards Signaling Pages: 10

POWERBOSS 01648-1

Brand: Briggs & Stratton Pages: 36

Brand: Briggs & Stratton Pages: 32

Brand: Briggs & Stratton Pages: 84

Brand: Briggs & Stratton Pages: 44

Brand: Briggs & Stratton Pages: 28

Brand: Briggs & Stratton Pages: 48

Brand: Briggs & Stratton Pages: 37

Brand: Briggs & Stratton Pages: 72

Brand: Briggs & Stratton Pages: 6

Brand: DUROMAX Pages: 74

Brand: DUROMAX Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands