Honda DS-2CC102P(N)-IRT Owner'S Manual Download Page 73

Page: 73 / 115

STORAGE

Engine Oil

Change the engine oil (see page 56).

Engine Cylinder

1. Remove the spark plug (see page 60).

2. Pour a teaspoon (5 cc) of clean engine oil into the cylinder.

3. Pull the starter rope several times to distribute the oil in the cylinder.

4. Reinstall the spark plug (see page 60).

5. Slowly pull the starter grip until resistance is felt. At this point, the

piston is coming up on its compression stroke and both the intake
and exhaust valves are closed. Storing the engine in this position will
help to protect it from internal corrosion. Return the starter grip
gently.

Battery

Charge the battery before storing the generator (see page 66).

31Z37613.book 71 ページ２０１５年１２月３日　木曜日　午前９時３３分

Summary of Contents for DS-2CC102P(N)-IRT




















































































































Search results

Summary of Contents for DS-2CC102P(N)-IRT

Reviews:

Related manuals for DS-2CC102P(N)-IRT

Brands by name

Popular brands

Honda DS-2CC102P(N)-IRT, Owner'S Manual

Search results

Summary of Contents for DS-2CC102P(N)-IRT

Reviews:

Related manuals for DS-2CC102P(N)-IRT

Brands by name

Popular brands