Honda DS-2CC102P(N)-IRT Owner'S Manual Download Page 62

Page: 62 / 115

SERVICING YOUR GENERATOR

SPARK PLUG SERVICE

In order to service the spark plug, you will need a spark plug wrench
(commercially available).

Recommended spark plug:

BPR6ES (NGK)

To ensure proper engine operation, the spark plug must be properly
gapped and free of deposits.

An incorrect spark plug can cause engine damage.

If the engine is hot, allow it to cool before servicing the spark plug.

1. Open the left maintenance cover by turning its latch

counterclockwise.

2. Loosen the cover screw and remove the spark plug inspection cover.

3. Disconnect the spark plug cap, and remove any dirt from around the

spark plug area.

4. Remove the spark plug with a spark plug wrench.

COVER SCREW

SPARK PLUG INSPECTION COVER

SPARK PLUG WRENCH

SPARK PLUG CAP

31Z37613.book 60 ページ２０１５年１２月２日　水曜日　午前１０時４５分

Summary of Contents for DS-2CC102P(N)-IRT




















































































































Search results

Summary of Contents for DS-2CC102P(N)-IRT

Reviews:

Related manuals for DS-2CC102P(N)-IRT

Brands by name

Popular brands

Honda DS-2CC102P(N)-IRT, Owner'S Manual

Search results

Summary of Contents for DS-2CC102P(N)-IRT

Reviews:

Related manuals for DS-2CC102P(N)-IRT

Brands by name

Popular brands