Honda DS-2CC102P(N)-IRT Owner'S Manual Download Page 29

Page: 29 / 115

BEFORE OPERATION

Check the Engine

• Before each use, look around and underneath the engine for signs of

oil or gasoline leaks.

• Check the engine oil level (see page 55). A low engine oil level will

cause the Oil Alert system to shut down the engine.

• Check the air filters (see page 58). Dirty air filters will restrict air flow

to the fuel system, reducing engine and generator performance.

• Check the fuel level (see page 53). Starting with a full tank will help

to eliminate or reduce operating interruptions for refueling.

Check the GFCI

Check the GFCI operation (see page 35) after starting the engine.

Battery Maintenance Cover

Never operate the generator without the battery maintenance cover in
place, as poor engine and generator performance will result.

BATTERY MAINTENANCE COVER

31Z37613.book 27 ページ２０１５年１２月３日　木曜日　午前９時３３分

Summary of Contents for DS-2CC102P(N)-IRT




















































































































Search results

Summary of Contents for DS-2CC102P(N)-IRT

Reviews:

Related manuals for DS-2CC102P(N)-IRT

Brands by name

Popular brands

Honda DS-2CC102P(N)-IRT, Owner'S Manual

Search results

Summary of Contents for DS-2CC102P(N)-IRT

Reviews:

Related manuals for DS-2CC102P(N)-IRT

Brands by name

Popular brands