Honda DS-2CC102P(N)-IRT Owner'S Manual Download Page 57

Page: 57 / 115

SERVICING YOUR GENERATOR

ENGINE OIL LEVEL CHECK

Check the engine oil level with the engine stopped and in a level
position.

1. Open the right maintenance cover by turning its latch

counterclockwise.

2. Remove the oil filler cap.

3. Check the oil level. If it is below the upper limit, fill with the

recommended oil (see page 57) to the upper limit of the oil filler
neck.

4. Reinstall the oil filler cap securely.

5. Close the right maintenance cover by turning its latch clockwise.

The Oil Alert system will automatically stop the engine before the oil
level falls below safe limits. However, to avoid the inconvenience of an
unexpected shutdown, check the oil level regularly.

OIL FILLER NECK

OIL FILLER CAP

UPPER LIMIT

31Z37613.book 55 ページ２０１５年１２月２日　水曜日　午前１０時４５分

Summary of Contents for DS-2CC102P(N)-IRT




















































































































Search results

Summary of Contents for DS-2CC102P(N)-IRT

Reviews:

Related manuals for DS-2CC102P(N)-IRT

Brands by name

Popular brands

Honda DS-2CC102P(N)-IRT, Owner'S Manual

Search results

Summary of Contents for DS-2CC102P(N)-IRT

Reviews:

Related manuals for DS-2CC102P(N)-IRT

Brands by name

Popular brands