Honda DS-2CC102P(N)-IRT Owner'S Manual Download Page 107

Page: 107 / 115

105

OPTIONAL PARTS

HANGER KIT

Protect the fuel tank and frame pipe with the protector films during
installation of the hanger.

1. Slide one end of the hanger under the frame pipe on the left side of

the generator.

2. Slide the other end of the hanger under the frame pipe on the right

side of the generator.

3. Slide the hanger along the frame pipes to align the center of the

hanger with the recessed part on the rear side of the fuel tank.

4. Install the hanger brackets on both ends of the hanger and tighten

the 8×16 mm flange bolts securely.

TORQUE:

17–22 lbf·ft (24–29 N·m, 2.4–3.0 kgf·m)

PROTECTOR FILM
(commercially available)

HANGER

8×16 mm FLANGE BOLT (4)

HANGER
BRACKET (2)

HANGER

31Z37613.book 105 ページ２０１５年１２月２日　水曜日　午前１０時４５分

Summary of Contents for DS-2CC102P(N)-IRT




















































































































Search results

Summary of Contents for DS-2CC102P(N)-IRT

Reviews:

Related manuals for DS-2CC102P(N)-IRT

Brands by name

Popular brands

Honda DS-2CC102P(N)-IRT, Owner'S Manual

Search results

Summary of Contents for DS-2CC102P(N)-IRT

Reviews:

Related manuals for DS-2CC102P(N)-IRT

Brands by name

Popular brands