Honda DS-2CC102P(N)-IRT Owner'S Manual Download Page 101

Page: 101 / 115

INITIAL USE INSTRUCTIONS

ENGINE OIL

The generator is shipped

WITHOUT OIL

in the engine.

1. Place the generator on a level surface.

2. Open the right maintenance cover by turning its latch counterclockwise.

3. Remove the oil filler cap.

4. Add enough oil to bring the oil level to the upper limit of the oil filler

neck. SAE 10W-30 API service category SJ or later (or equivalent) is
recommended for general use; for additional recommendations
(see page 57).

Maximum oil capacity:

1.16 US qt (1.10 L)

Do not overfill the engine with oil.

If the engine is overfilled, the

excess oil may be transferred to the air cleaner housing and air filter.

5. Reinstall the oil filler cap securely.

6. Close the right maintenance cover by turning its latch clockwise.

UPPER LIMIT

OIL FILLER CAP

OIL FILLER NECK

31Z37613.book 99 ページ２０１５年１２月２日　水曜日　午前１０時４５分

Summary of Contents for DS-2CC102P(N)-IRT




















































































































Search results

Summary of Contents for DS-2CC102P(N)-IRT

Reviews:

Related manuals for DS-2CC102P(N)-IRT

Brands by name

Popular brands

Honda DS-2CC102P(N)-IRT, Owner'S Manual

Search results

Summary of Contents for DS-2CC102P(N)-IRT

Reviews:

Related manuals for DS-2CC102P(N)-IRT

Brands by name

Popular brands