Honda CRF125F 2022 Owner'S Manual Download | Manualshive

Page: 57 / 132

background image

47

Flooded Engine

(Using the start button)
If the engine fails to start after repeated
attempts, it may be flooded with excess fuel.
To clear a flooded engine, open the throttle
fully and press the start button for 5 seconds.
Follow the normal engine starting procedure

(page 46).

(Using the kickstarter)
If the engine fails to start after repeated
attempts, it may be flooded with excess fuel.
To clear a flooded engine, open the throttle
fully and crank the engine several times with
the kickstarter. Follow the normal engine
starting procedure (page 46).

Ignition Cut Off

Your motorcycle is designed to automatically
stop the engine and fuel pump if the
motorcycle is over-turned (a banking sensor

cuts off the ignition system).

«
...
55
56
57
58
59
...
»

Summary of Contents for CRF125F 2022





































































































































Reviews:

No comments

Related manuals for CRF125F 2022

Brand: Cannondale Pages: 61

Brand: R&G Pages: 2

Brand: Biltema Pages: 2

Brand: Honda Pages: 137

Brand: Kabuto Pages: 20

Brand: Baja motorsports Pages: 20

Brand: R&G Pages: 9

Brand: DYNATEK Pages: 5

Brand: Arai Helmet Pages: 12

Brand: hepco & becker Pages: 3

Brand: Ducati Pages: 27

Brand: Chicago Electric Pages: 12

Brand: Shark Pages: 28

Brand: BUMOT Pages: 5

Brand: APRILIA Pages: 80

Brand: Rockford Fosgate Pages: 8

Brand: Rockford Fosgate Pages: 17

RST MILLE FUTURA - PART 1 2000

Brand: APRILIA Pages: 58

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands