background image

wwwClassicCyclesOrg

6

SUSPENSON

The front and rear suspension of this motorcycle can provide the desired ride under various rider/luggage weights and driving
conditions through adjustment of the air pressure.

The recommended pressures under normal conditions are:

Front

0 - 40 kPa (0 - 0.4 kg/cm

2

, 0 - 6 psi)

Rear

0 - 400 kPa (0 - 4.0 kg/cm

2

, 0 - 57 psi)

Low air pressure settings provide a softer ride and for light loads and smooth road conditions. High air pressure settings
provide a firm er ride and are for heavy loads and rough road conditions.

Front Air Pressure

Rear Air Pressure

Conditions

Rider/Load

Driving Conditions

0 kPa

(0 kg/cm2)

(0 psi)

40 kPa

(0.4 kg/cm

2

)

(6 psi)

0 kPa

(0 kg/cm2)

(0 psi)

400 kPa

(4.0 kg/cm

2

)

(57 psi)

One

Up to *

180 kg (397 lbs)

Ordinary or city road

driving

Rough road driving

*The combined weight of the rider, passenger, luggage and all accessories.

Air Pressure

Check and adjust air pressure when the front fork tubes and rear shock absorbers are cold
before riding.

Front air pressure adjustment:

1.

 

Place the motorcycle on its centre stand. Do not use the side stand, or you will get false

pressure readings.

2.

 

Remove the front fork air valve cap (1). Check the air pressure.

NOTE: Some pressure will be lost when removing the gauge from the valve. Determine

the amount of loss and compensate accordingly.

3.

 

Add air to the recommended pressure.

NOTE: We recommend that you do not exceed the recommended air pressure or the ride will be harsh and
uncomfortable.

4.

 

Reinstall the front fork air valve cap.

Rear air pressure adjustment:

1.

 

Place the motorcycle on its centre stand.

2.

 

Do not use the side stand, or you will get false pressure readings.

3.

 

Remove the right side cover.

4.

 

Remove the valve air cap (2). Check the air pressure with an air pressure gauge.

NOTE: Some pressure will be lost when removing the gauge from the valve.

Determine the amount of loss and compensate accordingly.

5.

 

If required, add air up to the recommended pressure.

6.

 

Reinstall the air valve cap (2) and the right side cover.

Summary of Contents for CBX 750F

























Reviews: