Honda CBR650F 2014 Owner'S Manual Download Page 91

Page: 91 / 133

Tire Puncture

Removing Wheels

continued

ou
bles

hoo

ting

When removing and installing the wheel, be
careful not to damage the wheel speed
sensor and pulser ring.

❙

Front Wheel

Removal

Park on a firm, level surface.

Cover both sides of the front wheel and
brake calipers with protective tape or cloth.

On the left side, remove the mounting
bolts and remove the brake caliper

On the right side, remove the mounting
bolts and brake caliper.

Support the brake caliper assembly so
that it doesn’t hang from the brake
hose. Do not twist the brake hose.

Avoid getting grease, oil, or dirt on
the disc or pad surfaces.

Do not pull the brake lever while the
brake caliper is removed.

Take care to prevent the brake caliper
from scratching the wheel during
removal.

CBR650FA only

Mounting
bolts

Brake caliper

Tape or cloth

Wheel speed sensor
(CBR650FA only)

Pulser ring
(CBR650FA only)

Summary of Contents for CBR650F 2014






































































































































Search results

Summary of Contents for CBR650F 2014

Reviews:

Related manuals for CBR650F 2014

Brands by name

Popular brands

Honda CBR650F 2014, Owner'S Manual

Search results

Summary of Contents for CBR650F 2014

Reviews:

Related manuals for CBR650F 2014

Brands by name

Popular brands