background image

2

HomewerksWW.com

PRODUCT SPECIFICATIONS

Max. Flow Rate: 

1

.2 GPM (4.54 LPM) at 60 PSI

Washerless cartridges

ASME A

11

2.

1

8.

1

/CSA B

1

25

Manufactured to include no more than 0.25% weighted average lead content 

on wetted surfaces

NSF 6

1

-9

Polished chrome finish

Total weight of item: 2.34 lbs.

ASSEMBLY INSTRUCTIONS

1

.  Turn off water at the supply valve 

under the sink or at the main water 

supply. Disconnect the supply lines to 

the faucet and remove the old faucet.
Clean and dry the surface area 

where the new faucet will be 

mounted.

1

5.

Apply silicone to the underside of 

the flange (5.

1

). From underneath 

the sink, insert the pop-up drain 

assembly (C) into the drain opening 

(5.2) in the sink. From above the 

sink, screw the flange (5.

1

) onto the 

pop-up drain assembly (C). The 

pivot hole (5.3) must face the back 

of the sink. 
Use groove joint pliers to tighten 

the nut (5.4) or the sealant may not 

seal properly. Do not overtighten. 

Clean away any excess silicone. 

Open the easy install rotating  

clip (5.5).

sil

ico

ne

5.3

5.4

C

5.1

5.2

5.5

5

2.  Ensure the gasket (2.

1

) is in place on 

the bottom of the faucet body (A). 

Apply a thin bead of silicone sealant 

to the underside of the gasket (2.

1

on the faucet body (A). Insert the 

faucet body (A) through the 

mounting holes in the sink (2.2). 

Secure the faucet body (A) to the 

sink using the mounting nuts (D).

D

A

2.1

2.2

2

6.

Insert the stopper (6.

1

) down into 

the pop-up drain assembly (C). 

Install the horizontal rod (6.2) 

from the lift rod assembly (B) into 

the pivot hole (6.3) in the pop-up 

drain assembly (C) as shown in 

figure B. Make sure the horizontal 

rod (6.2) is inserted completely 

into the pop-up drain assembly 

(C) and that it engages with the 

stopper (6.

1

), as shown in figure A. 

Close the easy install rotating  

clip (6.4).

6.1

6.1

6.2

C

6.2

6.3

6.3

6.4

Figure A

Figure B

6

3. To connect the water supply, use 

1

/2 in. IPS faucet supply lines (3.

1

or coupling nuts (3.2) with 3/8 in. 

O.D. ball-nose risers (3.3).
Wrap thread seal tape around each 

faucet shank (3.4) in a clockwise 

direction. Use a wrench to tighten 

each supply line (3.

1

) fitting or 

coupling nut (3.2) to the faucet 

shanks (3.4). Do not overtighten. 

3.3

3.4

3.1

3.2

3

7.

If the horizontal rod (7.

1

) is too 

long, as shown in figure A, the 

length can be adjusted. 
As shown in figure B, remove the 

clip (7.2) from the horizontal rod 

(7.

1

). Slide the plastic portion of 

the rod to adjust to the desired 

length. The excess length (7.3) can 

be removed where perforated by 

snapping it off with pliers or cutting 

it off with a saw. 
After the plastic portion of the 

horizontal rod (7.

1

) is positioned 

properly, reinstall the clip (7.2) as 

shown in figure C. 

7.

Wall

1

7.2

7.1

7.3

7.1

7.2

Figure A

Figure B

Figure C

7

4. Remove the stopper (4.

1

) and 

flange (4.2) from the pop-up drain 

assembly (C). Screw the attached 

mounting nut (4.3) down the pop-up 

drain assembly (C) and then push the 

gasket (4.4) down.

4.1

4.2

C

4.3

4.4

4

Reviews: