background image

NEVER

use glass cleaners on

finished furniture. Ammonia

chemically attacks the finish.

allow liquids to remain on furniture.

Absorption causes parts to warp

and split and finishes to delaminate.

NEVER

CARE INSTRUCTIONS

Do not use rubber

based placemats.

PREVENT

DISCOLORING

Do not use commercial

waxes and polishes.

PREVENT

YELLOWING

Do not place hot

objects on surface.

PREVENT

FINISH DAMAGE

Do not write

directly on surface.

PREVENT

MARKING

Do not use power tools

above 8 volts to assemble.

PREVENT

CRACKING

Do not place

in direct sunlight.

PREVENT

FADING

with a soft cloth moistened

in lukewarm soap and water.

Buff with a dry clean cloth.

CLEAN

home

styles will provide replacements free of charge for missing or damaged parts within 30 days of purchase.

Digital images of the defective parts may be required. If the product was not purchased from an authorized retailer,

home

styles is under no obligation to provide replacement parts. Parts are not available for fully assembled items nor

are parts available for sale. Replacements for missing or damaged parts may be requested via contact info below.

styles Customer Service: www.homestylesfurniture.com,

home

[email protected],

888-680-7460

Summary of Contents for 5001-006


















Reviews: