Homelite UT10514 Replacement Operator'S Manual Download Page 35

Page  

LIMITEd WARRANTy STATEMENT

Homelite Consumer Products, Inc., (“Homelite”)

 warrants 

to the original retail purchaser that this HOMELITE

 brand 

outdoor  product  is  free  from  defect  in  material  and 
workmanship and agrees to repair or replace, at Homelite’s, 
discretion, any defective product free of charge within these 
time periods from the date of purchase.

  One year for the following units if used for personal, 

family,  or  household  use:  all  MightyLite  26CS  and 
MightyLite 26B models;

  Two  years  for  all  other  models  if  used  for  personal, 

family, or household use;

  90 days for any unit used for other purposes, such as 

rental or commercial.

This  warranty  extends  to  the  original  retail  purchaser 
only  and  commences  on  the  date  of  the  original  retail 
purchase.
Any  part  of  the

  this  product  manufactured  or  supplied 

by  Homelite

  and  found  in  the  reasonable  judgment  of 

Homelite

 to be defective in material or workmanship will 

be repaired or replaced without charge for parts and labor   
by a Homelite authorized service center. 
The product, including any defective part, must be returned 
to an authorized service dealer within the warranty period. 
The expense of delivering the

 product to the dealer for 

warranty work and the expense of returning it back to the 
owner after repair or replacement will be paid by the owner. 
Homelite’s

 responsibility in respect to claims is limited to 

making the required repairs or replacements and no claim 
of breach of warranty shall be cause for cancellation or 
rescission of the contract of sale of any HOMELITE

 brand 

product. Proof of purchase will be required by the dealer 
to substantiate any warranty claim. All warranty work must 
be performed by a Homelite authorized service center. 
This warranty is limited to ninety (90) days from the date of 
original retail purchase for any HOMELITE

 brand product 

that is used for rental or commercial purposes, or any other 
income-producing purpose.
This warranty does not cover any HOMELITE

 brand product 

that has been subject to misuse, neglect, negligence, or 
accident, or that has been operated in any way contrary 
to the operating instructions as specified in this

 operator’s 

manual. This warranty does not apply to any damage to 
the

 product that is the result of improper maintenance or 

to any 

 product that has been altered or modified. The 

warranty  does  not  extend  to  repairs  made  necessary 
by  normal  wear  or  by  the  use  of  parts  or  accessories 
which  are  either  incompatible  with  the  HOMELITE  
brand  product

  or  adversely  affect  its  operation, 

performance, or durability. In addition, this warranty does 
not cover:

A.  Tune-ups  –  Spark  Plugs,  Carburetor,  Carburetor 

Adjustments, Ignition, Filters

B.  Wear  items  –  Bump  Knobs,  Outer  Spools,  Cutting 

Lines, Inner Reels, Starter Pulleys, Starter Ropes, Drive 
Belts, Tines, Felt Washers, Hitch Pins, Mulching Blades, 
Blower Fans, Blower and Vacuum Tubes, Vacuum Bags 
and Straps, Guide Bars, Saw Chains

Homelite

  reserves  the  right  to  change  or  improve 

the  design  of  any  HOMELITE  brand  product  without 
assuming any obligation to modify any product previously 
manufactured.
ALL IMPLIED WARRANTIES ARE LIMITED IN DURATION 
TO THE STATED WARRANTY PERIOD. ACCORDINGLY, 
ANY  SUCH  IMPLIED  WARRANTIES  INCLUDING 
MERCHANTABILITY,  FITNESS  FOR  A  PARTICULAR 
PURPOSE,  OR  OTHERWISE,  ARE  DISCLAIMED  IN 
THEIR  ENTIRETY  AFTER  THE  EXPIRATION  OF  THE 
APPROPRIATE TWO-YEAR, ONE-YEAR, OR NINETY-DAY 
WARRANTY PERIOD. HOMELITE’S OBLIGATION UNDER 
THIS  WARRANTY  IS  STRICTLY  AND  EXCLUSIVELY 
LIMITED  TO  THE  REPAIR  OR  REPLACEMENT  OF 
DEFECTIVE PARTS AND HOMELITE DOES NOT ASSUME 
OR AUTHORIZE ANYONE TO ASSUME FOR THEM ANY 
OTHER OBLIGATION. SOME STATES DO NOT ALLOW 
LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY 
LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY 
TO  YOU.  HOMELITE  ASSUMES  NO  RESPONSIBILITY 
FOR  INCIDENTAL,  CONSEQUENTIAL,  OR  OTHER 
DAMAGES INCLUDING, BUT NOT LIMITED TO, EXPENSE 
OF RETURNING THE PRODUCT TO AN AUTHORIZED 
HOMELITE  SERVICE  CENTER  AND  EXPENSE  OF 
DELIVERING  IT  BACK  TO  THE  OWNER,  MECHANIC’S 
TRAVEL TIME, TELEPHONE OR TELEGRAM CHARGES, 
RENTAL  OF  A  LIKE  PRODUCT  DURING  THE  TIME 
WARRANTY SERVICE IS BEING PERFORMED, TRAVEL, 
LOSS OR DAMAGE TO PERSONAL PROPERTY, LOSS 
OF  REVENUE,  LOSS  OF  USE  OF  THE  PRODUCT, 
LOSS  OF  TIME,  OR  INCONVENIENCE.  SOME  STATES 
DO NOT ALLOW THE EXCLUSION OR LIMITATION OF 
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE 
ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY 
TO YOU.
This warranty gives you specific legal rights, and you may 
also have other rights which vary from state to state.
This  warranty  applies  to  all  HOMELITE

  brand products 

manufactured by or for Homelite

 and sold in the United 

States and Canada.
To  locate  your  nearest  Homelite  authorized  service 
center, dial 1-800-242-4672 or log on to our website at  
www.homelite.com.

WARRANTy

Summary of Contents for UT10514 Replacement







































Reviews: