background image

5

SECTION 4 – ACTIVATING THE DIALER

Congratulations. Your Auto Dialer plus is now ready to help in emergency situations. You can

 

test how the Dialer works by pressing both # and * keys on the dialer’s keypad for the dialer 
to dial out to the phone numbers you have stored.

SECTION 5 - INSTRUCTION FOR THE RECIPIENT

There are several things that your call recipients should know in order to successfully receive 

and terminate an emergency call from your dialer.  Make sure your dialer recipients under

-

stand what to do when they receive your emergency call.  Therefore, it is a good idea to give 
them a copy of this page for their reference.

5.1 To START speakerphone conversation

After having fully listened to the recorded message, press the pound sign, to confirm that 

the message is NOT merely delivered to a voice mail. The “Listening-in” function press “1” and 

“Speaking-in” function press “ 3 ” can only be used when the call recipient pressed the pound 

key (#).  Time out period is 60 seconds and recipients can extend either the listening time 

or speaking time by pressing “1” or  “ 3 ” accordingly. Each time they are pressed a further 60 
seconds will be allowed by the Auto Dialer.

5.2 To EXTEND the time out for speakerphone conversation

Time out period is 60 seconds; the recipient can extend the time out for another 60

 

seconds 

by pressing (1) to listen-in and (3) to speak-in.  The conversation will be disconnected if the 
dialer receives no instruction.

5.3 To STOP the emergency message of the existing call AND all the

 

remaining calls

When the message is finished, press (#).  This will stop the dialer from calling existing number 

and all the remaining phone numbers.

Since this termination will stop the dialer from calling all the phone numbers, the recipient 

must know exactly the situation and emergency of the call before terminating it.

5.4 To DISCONNECT all calls after conversation

Once the speakerphone conversation is over, the recipient should disconnect the call by

 

pressing (#) instead of just hanging up the phone.  This will terminate the connection for

 

all 

existing call and the remaining calls.

Summary of Contents for 4902013























Reviews:

Related manuals for 4902013