EN - Quick Installation Guide – HGECO728 (HGPRO728), HGECO729 (HGPRO729), HGPRO828 (HGPLM828), HGPRO829
(HGPLM829)
Each Bullet or Dome camera is supplied with a mounting kit for attaching it to a wall. Before you affix the camera in position, please ensure the cable is of
adequate length to reach the DVR. We also recommend you try the camera with the DVR before mounting it, to ensure it in good working order, and help
diagnose created when installing it.
To mount the camera on a wall or ceiling, follow these instructions:
1. Ensure the surface you want to mount the camera on is solid and can support the weight.
2. Accurately mark on the wall the position of the holes to be drilled.
3. Drill to the correct depth in the wall, as indicated by the plugs.
4. Insert plugs into the drilled holes.
5. If required, drill a hole in the centre to feed the camera cable through the wall. Note the cable can be routed along the wall via the cut-out in the camera base.
6. Secure the camera to the wall using the provided screws.
Description of the picture:
A) Cut-out, B) Mounting Bracket, C) Base ring, D) Shroud, E) Main body
To adjust the camera´s position, loosen the screws at the base of the camera and the pivot point on the arm, as well as the locking ring on the bracket. The
camera is now free to be positioned at any angle. Once positioned, tighten both screws and locking ring again.
Safety precautions:
Use the device only and exclusively in accordance with this manual. Failure to follow instructions can lead to fire or damages to the device.
1. For safety reasons protect the device from falling, shortage of electric circuits and high temperatures. If the device or battery suffers from distortion and cause damage to the device,
stop using the device immediately.
2. Keep out of the reach of children. Only adult persons may use the device. Its owner is responsible for using of this device by other persons.
3. Do not expose the product to direct sunlight and heat radiation and do not cover it, i.e. it must have a permanent supply of colder ambient air.
4. Do not expose the product to direct contact with liquids (water); do not use any corrosive cleaning agents for cleaning including alcohol. Use only a dry cloth.
5. The device must meet the requirements needed to use direct current; using a different power source may cause fire or malfunction.
6. When using the product make sure that you have dry hands. Otherwise, it can cause damages to the product or electrical accident.
7. Set up the claim for warranty repair of device at your dealer. If you have technical questions or problems, contact your dealer.
8. For household use: The given symbol (crossed-out wheeled bin) on the product or at accompanying documents means that used electrical and
electronic products should not be disposed of with household waste. To ensure proper disposal of the product, hand it over to a designated collection
point, where it will be accepted free of charge. The correct disposal of this product will help to save valuable natural resources and prevent any potential
negative impacts on the environment and human health, which could otherwise be caused by inappropriate disposal of wastes. For more details, please,
contact your local authorities or the nearest collection point. The improper disposal of this waste can be penalized in accordance with national
regulations. Information for users to disposal of electrical and electronic devices (corporate and business use): For proper disposal of electrical and
electronic devices, ask for details from your dealer or distributor. Information for users to disposal of electrical and electronic devices in other countries
outside EU: The above mentioned symbol (crossed-out wheeled bin) is valid only in the countries of EU. For proper disposal of electrical and electronic
devices, ask for details from your authorities or dealer. All is expressed by the symbol of crossed-out wheeled bin on product, packaging or in printed
materials.
9.
To make a claim it is necessary to know the serial number of product, indicated on the back side of product and the packaging box. Please, keep the box with serial number
carefully for any complaints, you will avoid the unnecessary inconveniences or to be unable to establish a claim. Make a complaint of the product at your dealer, if not on website
www.iget.eu stated otherwise.
Individual parameters, description by figures and design may differ depending on the version and updates. For exact parameters and other product information visit the website
www.iget.eu. Printing errors reserved. The manufacturer and importer have no liability for data loss or other damages arising howsoever when using device.
Declaration of Conformity:
Company INTELEK spol. s r.o. hereby declares that all HGECO728 (HGPRO728), HGECO729 (HGPRO729), HGPRO828 (HGPLM828),
HGPRO829 (HGPLM829) devices are in compliance with essential requirements and other relevant provisions of Directive
2004/108/EC. The products are intended for sale without limitation in the Czech Republic, Slovakia, Poland, Bulgaria, Germany,
Austria, Belgium, Denmark, Finland, Greece, Netherlands Ireland, Great Britain, Norway, France, Spain, Italy, Hungary, Lithuania, Latvia,
Estonia, Romania and other member countries of EU and in Russia. The warranty period of the product is 24 months, unless stated
otherwise. The Declaration of Conformity can be downloaded from the website
Exclusive importer of Homeguard products to EU:
INTELEK spol. s r.o., Ericha Roučky 1291/4, 627 00 Brno, Web:
Copyright © 2016 INTELEK spol. s r.o. All rights reserved.
CZ - Rychlá instalace - HGECO728 (HGPRO728), HGECO729 (HGPRO729), HGPRO828 (HGPLM828), HGPRO829 (HGPLM829)
A)
B)
C)
D)
E)
