Instructions for Use
1. Ensure that the unit is unplugged before filling. Turn the cap
(See Figure 1) counter-clockwise one-half rotation and remove.
2. Add one packet of the provided water conditioner to the unit.
Any time that you fill the unit with water, water conditioner must be
added. You may leave water in the massager for up to 6 months.
NOTE: Once you have used all of the provided water conditioner, you
may use any commercially available water conditioner for waterbeds. It
is often located in the bedding section of general merchandise stores.
The amount to be added is 1/2 oz. (approx. one tablespoon) and not the
amount recommended for a waterbed mattress.
3. Fill with water to the red fill line located inside the spout (See Figure
2). Do not fill higher than the fill line.
4. Replace the cap by placing it upside down on the spout (See Figure
3) and turn clockwise half a rotation. The cap should lock into place.
5. Plug the unit into a 120-volt household outlet.
6. To turn the unit ON, press the silver button in the center of the control
panel (see Figure 4).
a. The first press of the button will activate the invigorating
vibration massage. The blue Massage button will illuminate to
confirm your selection and the water mattress will also be
illuminated in blue.
b. The second press of the button will activate the Heat feature
with the massage. The red Heat button will illuminate to
confirm your selection and the water mattress will also be
illuminated in red.
NOTE: Water heat will only work while the massage feature is on.
It will take approximately 3 minutes for the water to heat up.
c. The third press of the button will turn the unit OFF.
7. Enjoy the massage by resting your feet or sliding them across the
water mattress. NOTE: You must be seated to use the massager.
Do not stand on the massager.
8. When you are finished using your massager, turn the unit off and
unplug it.
9. You may leave water in your massager for up to 6 months. If you are
not going to use it for an extended period of time, it would be best to
empty the water.
To empty: First, unplug the unit. Second, turn the cap counter-clockwise
one-half rotation and remove as noted in Step 1. Then tip the unit,
allowing water to flow out of the spout. DO NOT pour water over the
control panel.
6
7
Float
Massaging Waterbed for the Feet
TM
Water Fill Line
Water Mattress
Spout
Removable Cap
Cord Storage
Control Panel
Heat Indicator
Power Button
Massage Indicator
CAUTION: DO NOT FILL
WATER OVER THE RED
FILL LINE
CAUTION: NEVER TURN
MASSAGER ON
WITHOUT WATER IN IT
Figure 2
Figure 3
Figure 4
Maintenance
To Clean
Unplug the unit and allow it to cool before
cleaning.
• Clean the exterior with a soft, damp cloth and
a mild cleansing agent.
• If necessary, you may periodically clean the
inside of the water mattress by filling it with a
solution of 10 parts water to 1 part household
bleach as needed. After approximately 5
minutes time, pour out the water-bleach
solution. Refill with water and then pour it
back out to rinse out the water mattress.
DO NOT operate the unit with the water-
bleach solution.
• After cleaning, wipe surfaces with a dry cloth.
• Never use strong abrasives, detergents or
cleansing agents except as noted with the
water-bleach solution.
• Periodically straighten the cord if it
becomes twisted.
To Store
Unplug the appliance from the outlet and allow
to cool.
• Empty the water as noted in Step 9 in the
Instructions for Use.
• Wipe the unit with a dry cloth.
• Store in its box or a clean, dry place.
• Wrap the power cord around the cord storage
in the bottom of the unit.
• To avoid breakage, do not wrap the power
cord around the unit.
• Do not hang the unit by the power cord.
Figure 1
