12
13
Step 5: Level your washer
See if the washer is leveled by checking the position of the tub or using a leveling gauge.
1. Slide the washer into position.
2. Open the lid of the washer, and pour the water into the tub to just below the pulsator level.
3. If the washer is leveled, the pulsator is positioned at the center of the washer as shown
in the figure. If not, level your washer by turning the front leveling feet clockwise or
counterclockwise as necessary.
NOTE: There is ONLY ONE adjustable leg on this washer.
Step 6: Power on your washer
Plug the power cord into a 3-prong, well grounded 120V 60Hz approved
electrical outlet protected by a 15-amp fuse or comparable circuit breaker.
Your washer is grounded through the third prong of the power cord when
plugged into a 3-prong grounded electrical outlet.
Step 7: Run a test cycle
Run a test cycle as follows to check if your washer is properly installed.
1. Load about 3.5 pounds of laundry into the tub.
2. Press the ON/OFF button to turn on your washer.
3. Select the Rinse+Spin cycle.
4. Press the Start/Pause button to start the test cycle.
5. The washer should not rock or vibrate excessively when water is supplied, washing or spinning, and should drain well
during the spin cycle.
WARNING:
If there is a water leak while filling or draining, check the water connections.
If the washer rocks and vibrates excessively, level your washer again.
Step 8: Store your washer
If you want to store your washer in another location, unplug it, drain any remaining water from the drain pipe and hook the
pipe onto the back of the washer.
Disconnect the water inlet hoses from the faucets and move the washer to a new location.
Control Panel
INSTALLATION INSTRUCTIONS
OPERATION
1 Program
Press this button to select your desired washing program: Heavy (light), Gentle (light), Normal (light), Rapid (light) and Soak (light).
2 Load Size
Press this button to set your washing load size. Your setting will decide the water level throughout all steps.
3 Wash
Press the button to select the washing time.
4 Digital display
The digital display will show and count down the estimated minutes for the wash cycle selected.
5 Rinse
Press the button to select the times of rinse.
6 Spin
Press the button to select the time of spin.
7 START/PAUSE
Press the START/PAUSE button once to the start the wash cycle. Press the button during operation to pause the cycle. Press
again to continue the cycle.
8 ON/OFF
Press the button once to turn ON the power. Press again to turn OFF. Washing a load of laundry.
Step 1: Power on your washer
Press the ON/OFF button to power on.
Step 2: Load your washer
WARNING:
Before loading your laundry, be sure to take out coins, keys and other hard objects, and close
all zippers to prevent the clothes from damage.
Sort laundry by fabric type, soil level, color and load size as needed. Refer to the Fabric Care Chart. Fill
the tub with dry, unfolded clothes, but DO NOT OVERLOAD the tub. Load the tub no more than 3/4 full.
To ensure good cleaning results do not overload the tub, especially when washing heavily soiled loads.
Never load the tub more than 3/4 full.
WARNING:
Overloading may reduce washing efficiency, cause excess wear, and possibly cause creasing or
wrinkling of items in the load.
Note: To add a forgotten item:
1. Press the START/PAUSE button to pause the washer.
2. Wait for the tub to stop running. Then open the lid.
3. Add the items, close the lid, and then press the START/PAUSE button. The cycle will resume.
Step 3: Add detergent
This washer is designed for high efficiency (HE) powder detergent only. Add the recommended
amount of detergent directly into the tub before starting your washer. The normal amount of
detergent to use is 1/4 to 1/2 of the maximum amount recommended by the detergent manufacturer.
Always reduce the amount of detergent if the load is small or light, or if your water is very soft. Never
use more than the maximum amount recommended by the detergent manufacturer.
WARNING:
Never pour any liquid bleach directly onto the load. It can cause fabric damage, such as
weakening of cloth fibers or color loss.
Step 4: Select your desired cycle and options
1. Select your desired washing program.
2. Select the water level based on a High, Medium or Low.
Press the Load Size button to change the water level setting (3-Large, 2-Medium, 1-Small)
3. Select any combination among WASH, RINSE and SPIN modes according to the dirty degree.
Refer to the detailed operation methods as following:
Continuously press the washing button to select washing time.(1~15 minutes, or no wash process)
Continuously press the rinse button to select rinse times.(1~3 times, or no rinse process)
Continuously press the spin button to select the spin time.(1~9 minutes or no spin process)
Step 5: Start the cycle
Press the START/PAUSE button to start the washing cycle. When the washing cycle begins, the
Estimated Time in minutes for the cycle to complete will show and count down in the digital
display.
WARNING:
When the washer is running, you should pause the program and
wait for it to stop completely before you open the lid.
OPERATION