3/3
STEP 8
STEP 9
NOTE: The Stir Stick has size-specific connections and can only be assembled one way.
First, slide the (P-2) Middle Stir Stick down through the hole in the hand of the (I) Right Arm as
shown. Then, slide the (P-3) Middle Stir Stick up through the hole in the hand of the (J) Left
Arm, and twist counter-clockwise to secure. Then attach the (P-1) Top Stir Stick to the top of
the (P-2) Middle Stir Stick, assemble the (P-3)&(P-4)&(P-5)) Middle Stir Sticks to each other to
the (P-6) Lower Stir Stick as shown. Next, set the (P-6) Lower Stir Stick into the mechanism
located on the (M) Cauldron as shown.
A2
A2
A3
A3
A1
A1
M
A
A
Set Assembled (M) Cauldron onto (A) Base by attaching the slots located at the front of (A) Base as
shown.
Connect A1, A2, A3 cables from the (M) Cauldron to the coordinating cables from the Function control
box on (D) Torso Frame through the (H) Costume.
STEP 7
Insert the tips of each flexible support rod
into the fabric slots sewn to the inside of
the Cauldron
M
M
N
Slot
Sensor
Elastic Band
O
O
Assemble the (M) Cauldron by sliding the ends of each (N) Cauldron Support Poles into the fabric
pouches found at the top and bottom of the inside of the cauldron
as shown in Figure 1.
Attach the top center of the (O)
Cauldron Light Support Frame on the top of the cauldron using
elastic band as shown in Figure 2.
Insert Poles of the (O)
Cauldron Light Support Frame
into the slots located on the cauldron base
as
shown in Figure 3
.
NOTE: Sensor located at the front of
cauldron under the (O)
Cauldron Light
Support Frame.
M
P-6
P-5
P-4
P-3
P-2
P-1
I
I
J
J
OPERATION INSTRUCTIONS:
1. Plug the Adapter into a standard power outlet and adjust the settings on the Function Control Box,
located on the (D) Torso Frame , as desired.
2.
Settings:
Sensor : This switch mode will only activate lights, sound, and animation when the Infra-red (IR) sensor
is activated. The item will operate for 1 audio-cycle with each sensor activation. The Infra-red
(IR) sensor will activate when someone comes within an 80-degree angle from left-to-right, as
well as from above and below. The Infra-red (IR) sensor has a range of up to 2 m / 6.5 ft.
: OFF - This switch mode will turn the lights, sounds, and animation off.
I
: ON
-
This switch mode will continually operate the lights, sound, and animation of the item.
: Raise or lower the volume using the volume control turn dial, turn and click all the way down to
turn the volume off.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures: Reorient or relocate the receiving antenna, Increase the separation between the equipment and receiver,
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or
experienced radio/TV technician for help.
CAN ICES-3 (B)/ NMB-3 (B)
Sensor / Détecteur
5.9 V
Try me / Essaie-moi / Pruébame
1
2
3
