Safety Information
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical products, basic precautions should always be
followed including the following:
a)
READ AND FOLLOW ALL
SAFETY INSTRUCTIONS.
b) This product is for indoor use only. The electrical rating 0.64 A 120 V
60 Hz.
c) Do not use this product outdoors.
d) This seasonal use product is not intended for permanent installation
or use.
e) Do not mount or place near gas or electric heaters, fireplace, candles
or other similar sources of heat.
f) Do not secure the wiring of the product with staples or nails, or place
on sharp hooks or nails.
g) Do not let lamps rest on the supply cord or on any wire.
h) Unplug the product when leaving the house, or when retiring for the
night, or if left unattended.
i) This is an electric product – not a toy! To avoid risk of fire, burns
personal injury and electric shock it should not be played with or placed
where small children can reach it.
j) Do not use this product for other than its intended use.
k) Do not hang ornaments or other objects from cord, wire, or light
string.
l) Do not close doors or windows on the product or extension cords as
this may damage the wire insulation.
m) Do not cover the product with cloth, paper or any material not part of
the product when in use.
n) Do not move the tree by pulling the tree tips or tree branches.
o)
This product contains an extension cord with a polarized plug (one
prong is wider than the other) as a feature to reduce the risk of
electrical shock. This plug will fit in a polarized outlet only one way. If
the plug does not fit fully in the outlet, reverse the plug. If it still does
not fit, contact a qualified electrician. Do not use with an extension
cord unless plug can be fully inserted. Do not alter or replace the
plug.
p) This product is equipped with push-in type lamps. Do not twist lamps.
q) This product employs overload protection (fuse). A blown fuse
indicates an overload or short-circuit situation. If the fuse blows, unplug
the product from the outlet. Also unplug any additional strings or
products that may be attached to the product. Replace the fuse as per
the user servicing instructions (follow product marking for proper fuse
rating) and check the product. If the replacement fuse blows, a
short-circuit may be present and the product should be discarded.
r) Read and follow all instructions that are on the product or provided
with the product.
s)
SAVE THESE INSTRUCTIONS.
CAUTION!
–
ALWAYS UNPLUG YOUR
TREE FROM ITS POWER SOURCE BEFORE
ASSEMBLING OR DISASSEMBLING.
7.5ft Dunland Fir LED Tree
SKU# 1007619306
Package Contents
A.
Top Section
Qty: 1
B.
Middle Section
Qty: 1
C.
Bottom
Section
Qty: 1
D.
Stand with an
eye bolt
Qty: 1
E.
Power Cord
Qty: 1
F.
Remote Control
Qty: 1
G.
Fuse
Qty: 1
H.
Rivet
Qty: 2
I.
Replacement
Bulb
Qty: 8
Assembling the tree stand
Step 1. Choose a location near a wall outlet.
Step 2. Open the stand to a 90 degree angle until the hole lines up with the
hole on the tube.
Step 3. Screw an eye bolt into the hole.
Assembling the tree
Please remove protective covers from the base of the pole for each tree
section before assembling.
Step 1. Carefully insert bottom section (C) of tree into tree base and
tighten the screw. (See Fig. 1)
Step 2. Insert the middle section (B) of the tree into the bottom section (C).
(See Fig. 2)
Step 3. Insert the top section (A) into the middle section (B). (See Fig. 3)
Step 4. Allow branches to fall into place or gently pull branches up and out.
When adjusting branches be sure that all wires are free of branch
hinges. (See Fig. 4)
Pre-Assembly
Assembly
