Step 8.
Please note this tree comes with a foot pedal switch and a
remote control for easy illumination and changing functions.
This tree is Color Changing, the 8 lighting options available are:
1.
Steady Warm White
2.
Flashing Warm White
3.
Fade In and Fade Out Warm White
4.
Steady Multicolor
5.
Flashing Multicolor
6.
Fade In and Fade Out Multicolor
7.
Sequential Multicolor & Warm White
8.
Color Changing
These functions can be changed by pressing the foot pedal
switch or using the remote control. Please see the instructions
of remote control below.
Turning on the tree
Step 1. Plug the well-connected power cord from the tree section (C) into
a proper outlet.
Step 2. Press the remote control or foot pedal switch to choose functions.
Instructions of Remote Control
Please note this tree has a remote control.
Please pull out the insulation tape from the remote control, before starting
to use it.
1.
Press Fn button, the function below cycle. Press the number key,
select from the following corresponding lighting functions:
Function 1: Steady Warm White
Function 2: Flashing Warm White
Function 3: Fade In and Fade Out Warm White
Function 4: Steady Multicolor
Function 5: Flashing Multicolor
Function 6: Fade In and Fade Out Multicolor
Function 7: Sequential Multicolor & Warm White
Function 8: Color Changing
If the remote control does not work, check whether the battery of the
remote control is out of power.
To replace the remote control battery:
1.
Replace with a new button cell “CR2025” (3 volt)
into the compartment.
CAUTION:
DO NOT DISPOSE OF
BATTERIES IN FIRE. BATTERIES MAY EXPLODE
OR LEAK.
CAUTION:
The product consists of non-replaceable LED
lamps. To reduce the risk of fire or electric shock, do not attempt to
replace lamps or modify string.
Care and Cleaning
Step 1. Remove all ornaments and decorations.
Step 2. Unplug the cord from the wall outlet and then disconnect each
section of the tree. Remove the power cords from the tree
bottom (C).
Step 3. Gently lift the tree top straight up to remove from the center
section and fold all branches towards the pole.
Step 4. Repeat this step for the center and bottom tree sections.
Step 5. Carefully place all tree sections into a shipping box and tape it
shut.
Step 6. Store your tree in a cool, dry place away from sunlight.
Troubleshooting
Problem Solution
The tree
does not
light
Ensure that all tree sections are connected into each
other well by pressing each section down and rotating.
Ensure that the power cord is plugged into the hole of
the connector found on the tree bottom (C). Make sure
power cord plug is securely inserted into a working
electrical outlet.
If you are still experiencing problems with the tree
please call 1-877-527-0313 for instructions.
Warning: Please note that changes or modifications not
expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference
by one or more of the following measures:
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and
receiver.
-
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-
Consult the dealer or an experienced radio/TV technician
for help.
Adapter Model No. TS-12W12V
Operation
